Abstract:Study design: An in vitro biomechanical study of various reconstructive techniques following decompression of the spondylotic cervical spine. OBJECTIVE.: To evaluate the biomechanical stability of anterior cervical plate fixation following three strategies of decompression for multilevel cervical spondylosis (three levels) of the cervical spine: three level discectomy, single corpectomy and discectomy, and a two-level corpectomy. Summary of background data: The main goals of surgical treatment for cervical myelopathy include adequate decompression and stabilization while maintaining or restoring cervical lordosis. Cervical decompression is often performed through a corpectomy followed by strut-graft reconstruction. An anterior cervical plate with end-fixation (two points of fixation) is then used to span the construct. The authors propose an alternative to multilevel corpectomy and long-segment end construct plate fixation. Often times, the cervical stenosis is confined to the area of the degenerative discs. As a result, the authors feel that either multilevel discectomy or a corpectomy combined with discectomy followed by segmental plate fixation may provide adequate decompression with increased biomechanical rigidity as compared to cervical plate-constructs with end-fixation only. Methods: Seven human cadaveric fresh-frozen cervical spines from C1-T1 were utilized. Three-dimensional motion analysis with an optical tracking device was used to determine motion following various reconstruction methods. All seven cervical spines underwent testing in a randomized order. The end construct model consisted of a corpectomy at C4 and C5 with a polymethyl methacrylate strut graft and an anterior cervical PEAK (DePuy-AcroMed) plate. The two segmental constructs also utilized the PEAK plate with one construct undergoing discectomies at C3-C4, C4-C5, and C5-C6 with polymethyl methacrylate interbody grafts and the other segmental construct undergoing a discectomy at C3-C4 and a corpectomy of C5. All specimens underwent a pure moment application of 2 Nm with regards to flexion-extension, lateral bending, and axial rotation. RESULTS.: The three-level discectomy and combined one-level discectomy and corpectomy with segmental fixation was significantly more rigid in flexion-extension and lateral bending than the two-level corpectomy with end-construct plate fixation (P < 0.05). There was no increase in stability during extension between the end construct (two-level corpectomy) reconstruction model and the un-instrumented corpectomy and grafted specimen. No difference was noted between the segmental constructs and the end-construct with regards to axial rotation. Conclusions: Cervical myelopathy is traditionally treated with a multilevel corpectomy and an end-construct plate fixation spanning the strut graft. A large moment arm is generated at the ends of the construct, potentially leading to plate migration or dislodgment. Often times, adequate decompression can be achieved with either a multilevel discectomy or a combined discectomy and corpectomy with segmental plate fixation. This study clearly demonstrates that segmental plate fixation affords a more biomechanically rigid method of reconstruction with regards to flexion-extension and lateral bending than end-construct plate fixation. The increased rigidity afforded by segmental fixation may significantly decrease the likelihood of plate dislodgement in the setting of anterior instrumentation alone following anterior alone, long segment reconstruction procedures.

Pedicle Screws Enhance Primary Stability in Multilevel Cervical Corpectomies: Biomechanical In Vitro Comparison of Different Implants Including Constrained and Nonconstrained Posterior Instumentations

Anterior Cervical Transpedicular Screw Fixation System in Subaxial Cervical Spine: A Finite Element Comparative Study.

The Impact of Cervical Pedicle Screws for Primary Stability in Multilevel Posterior Cervical Stabilizations

Biomechanical and Clinical Study of Anterior Transarticular Screw Fixation for Treatment of Traumatic Instability of C1-C2 Joint

Biomechanical Evaluation of Transfacet Screw Fixation for Stabilization of Multilevel Cervical Corpectomies

The Effect of Rod Pattern, Outrigger, and Multiple Screw-Rod Constructs for Surgical Stabilization of the 3-Column Destabilized Cervical Spine - A Biomechanical Analysis and Introduction of a Novel Technique

Biomechanical Analysis of Transpedicular Screw Fixation in the Subaxial Cervical Spine

Biomechanical stability of atlantoaxial and occipitocervical fixations with unilateral spinous process screw plus contralateral pedicle screw: a finite element analysis

Does pedicle screw fixation of the subaxial cervical spine provide adequate stabilization in a multilevel vertebral body fracture model? An in vitro biomechanical study

Enhancement of stability following anterior cervical corpectomy: a biomechanical study

Biomechanical study of anterior cervical corpectomy and step-cut grafting with bioabsorbable screws fixation in cadaveric cervical spine model.

Construct stability of an instrumented 2-level cervical corpectomy model following fatigue testing: biomechanical comparison of circumferential antero-posterior instrumentation versus a novel anterior-only transpedicular screw–plate fixation technique

Biomechanical Differences Between Transfacet and Lateral Mass Screw-Rod Constructs for Multilevel Posterior Cervical Spine Stabilization

Surgical management of two- versus three-column injuries of the cervicothoracic junction: biomechanical comparison of translaminar screw and pedicle screw fixation using a cadaveric model

Biomechanical Comparison of C1 Lateral Mass—C2 Short Pedicle Screw—C3 Lateral Mass Screw-Rod Construct Versus Goel-Harms Fixation for Atlantoaxial Instability

Morphological Character of Cervical Spine for Anterior Transpedicular Screw Fixation

Biomechanical evaluation of C1 lateral mass and C2 translaminar bicortical screws in atlantoaxial fixation: an in vitro human cadaveric study

Posterior spinal stabilization: A biomechanical comparison of Laminar Hook Fusion to a Pedicle Screw System

Types of Spinal Instability That Require Interbody Support in Posterior Lumbar Reconstruction: an in Vitro Biomechanical Investigation.

Biomechanical analysis on anterior transpedicular screw-fixation after two-level cervical corpectomy using finite element method