Abstract:Austenite formation behavior is investigated for the ferrite–pearlite initial microstructure, considering the influence of ferrite recrystallization and cementite distribution. Austenite transformation kinetics is well predicted by considering the varied nucleation density due to different recrystallization state. The proceeding of recrystallization postpones the austenite transformation kinetics, while getting rid of the interference of heating rate and nucleation location. In this study, the austenite formation behavior is investigated for the ferrite–pearlite initial microstructure, considering the influence of ferrite recrystallization and cementite distribution. Special attention is also given to the effect of recrystallization state on cementite distribution for varied heating routes. Austenite nucleation for varied recrystallization state is elucidated in terms of activation energy evaluation and post microstructural characterization, and the austenite transformation kinetics are modeled and experimentally validated. In the uncrystallized state, austenite forms on the original pearlite colonies quickly due to the short carbon diffusion path. The high activation energy leads to the exceptionally difficult nucleation at the ferrite–cementite interface inside ferrite matrix. Once recrystallization occurs partially, priority of austenite nucleation is on those ferrite boundaries (both recrystallized and unrecrystallized boundaries) decorated by cementite. With complete recrystallization, preferential nucleation sites are found to be junctions of ferrite–cementite interface on recrystallized ferrite boundaries. Austenite transformation kinetics is well predicted by considering the varied nucleation density due to different recrystallization state, showing a good agreement with experimental data. It is demonstrated directly by experimental evidence that proceeding of recrystallization postpones the austenite transformation kinetics, while getting rid of the interference of heating rate and nucleation location.

Difference in recrystallization behavior between lath martensite and deformed ferrite in ultralow carbon steel

Difference in Recrystallization Behavior between Martensite and Deformed Ferrite

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Microstructural evolution during the austenite-to-ferrite transformation from deformed austenite

Recrystallization of ferrite–austenite stainless steel

Discontinuous lath martensite transformation and its relationship with annealing twin of parent austenite and cooling rate in low carbon RAFM steel

Effects of acicular ferrites on crystallography and incomplete transformation of low-carbon low-alloy steel

Difference in transformation behavior between ferrite and austenite formations in medium manganese steel

Difference in thermodynamics between ferrite and martensite in the Fe-Ni system

Titanium‐Dependent Kinetics of Ferrite Single‐Phase Recrystallization in Cold‐Rolled Ultra‐High‐Strength Low‐Alloy Steels During Annealing

Unlocking the Mechanisms behind Austenite Formation of Cold‐Rolled Ferrite–Martensite Dual‐Phase Steels: The Role of Ferrite Recrystallization

Ultrafine Structure and High Strength in Cold-Rolled Martensite

Evaluation of Dislocation Density and Dislocation Strengthening Mechanism in Ultra Low-Carbon Martensitic Steel

Nanoscale austenite reversion through partitioning, segregation, and kinetic freezing: Example of a ductile 2 GPa Fe-Cr-C steel

Early Martensitic Transformation in a 0.74C–1.15Mn–1.08Cr High Carbon Steel

Difference between thermal-induced martensite and deformation-induced martensite in 304 austenitic stainless steel

Influence of the Temperature of High Pressure Torsion Deformation on the Recrystallization Kinetics of Iron with a Submicrocrystalline Structure

Microstructure Refinement via Nucleation of Intragranular Acicular Ferrite Stimulated by Ti-Containing Core–Shell Structured Particles in Low-Carbon Steel

Development of Very Tough Ferritic Stainless Steels by Optimizing the Recrystallized Microstructure

Effect of Austenitization Conditions on the Transformation Behavior of Low Carbon Steel Containing Ti⁻Ca Oxide Particles