Abstract:Cracking is one of the main causes for deterioration of concrete structures. Self-healing concrete with 3D-printed vascular networks has excellent potential for autonomous self-healing. This approach is scarcely investigated: no studies have been devoted to the influence of printing parameters on the properties of vascular based self-healing concrete. In this work, three-dimensional vascular structures with complex geometry were designed and printed with 4 different sets of printing parameters. First, the influence of the four, nominally identical, vascular networks on the initial flexural strength of self-healing concretes was experimentally investigated. In parallel, numerical modeling with a concrete damaged plasticity model (CDPM) in Abaqus software is used to simulate the influence of vascular networks on the mechanical properties of the self-healing composite. After the 4-point bending tests, epoxy resin is injected into the vascular networks as the healing agent to seal the cracks. Then, flexural strength regain and watertightness recovery were also measured. Based on the obtained results, we found that vascular based self-healing concretes have lower initial flexural strengths than the reference sample, as expected. The magnitude of the strength drop is shown to depend strongly on the printing parameters: the specimens with horizontally-printed vascular networks have higher flexural strength than the vertically-printed counterparts. Furthermore, vascular networks with a smaller printing layer-height have less influence on the initial flexural strength of vascular-based self-healing concrete compared to those with the larger printing layer-height. In terms of watertightness recovery, all tested vascular based self-healing samples showed a full (100%) recovery, which means that the printing direction and printing layer-height do not have an obvious effect on the watertightness recovery in this study. Numerical simulations of the mechanical performance of the composites with the CDPM show good agreement with the experiments, although printing quality of the vascular network influences the simulation accuracy. These simulations show great potential of using numerical simulations to design vascular based self-healing concrete in order to minimize a drop in mechanical properties, without compromising the healing efficiency. Overall, the designed 3D-printed vascular self-healing concretes show remarkable strength regain and watertightness recovery and provide a good basis for further research.

Networks of channels for self-healing composite materials

A two-dimensional micromechanical damage-healing model on microcrack-induced damage for microcapsule-enabled self-healing cementitious composites under tensile loading

An micro-level study on the cracking performance of encapsulation-based self-healing resin mineral composites under dynamic load based on XFEM

Self-healing cementitious composites with a hollow vascular network created using 3D-printed sacrificial templates

Active Healing of Microtubule-Motor Networks

Autonomic healing of polymer composites

Advanced 3D printed mini-vascular network for self-healing concrete

Three-Dimensional Percolation Modeling of Self-Healing Composites

Light self-healing of resin matrix composites based on pipe network carrier

Mechanical properties and healing efficiency of 3D-printed ABS vascular based self-healing cementitious composite: Experiments and modelling

An Adaptive Quasi-Continuum Approach for Modeling Fracture in Networked Materials: Application to Modeling of Polymer Networks

Modelling and simulation of coupled fluid transport and time-dependent fracture in fibre-reinforced hydrogel composites

An adaptive variational Quasicontinuum methodology for lattice networks with localized damage

Room‐Temperature Self‐Healing Soft Composite Network with Unprecedented Crack Propagation Resistance Enabled by Supramolecular Assembled Lamellar Structure

Linking cavitation and fracture to molecular scale structural damage of model networks

Self-healing and in-situ real-time damage-reporting fiber-reinforced composite

Multiscale and multiphysics discrete model of self-healing of matrix and interfacial cracks in fibre reinforced cementitious composites: Formulation, implementation and preliminary results

New Self-Repairing System for Brittle Matrix Composites Using Corrosion-Induced Intelligent Fiber

Tracking capsule activation and crack healing in a microcapsule-based self-healing polymer

Continuum damage-healing framework for the hydration induced self-healing of the cementitious composite

A multiscale analytical framework for mode I crack in staggered composites