Abstract:Na4Fe3(PO4)2(P2O7) is regarded as a promising cathode material for sodium-ion batteries due to its affordability, non-toxic nature, and excellent structural stability. However, its electrochemical performance is hampered by its poor electronic conductivity. Meanwhile, most of the previous studies utilized spray-drying and sol-gel methods to synthesize Na4Fe3(PO4)2(P2O7), and the large-scale synthesis of the cathode material is still challenging. This study presents a composite cathode material, Na4Fe2.94Al0.04(PO4)2(P2O7)/C, prepared via a straightforward ball-milling technique. By substituting Al3+ minimally into the Fe2+ site of NFPP, Fe defects are introduced into the structure, hindering the formation of NaFePO4 and thereby enhancing Na-ion diffusion kinetics and conductivity. Additionally, the average length of AlO bonds (2.18 Å) is slightly smaller than that of FeO bonds (2.19 Å), contributing to the superior structural stability. The smaller ionic radii of Al3+ induce lattice contraction, further enhancing the structural stability. Moreover, the surface of material particles is coated with a thin layer of carbon, ensuring excellent electrical conductivity and outstanding structure stability. As a result, the Na4Fe2.94Al0.04(PO4)2(P2O7)/C cathode exhibits excellent electrochemical performance, leading to high discharge capacity (128.1 mAh g-1 at 0.2 C), outstanding rate performance (98.1 mAh g-1 at 10 C), and long cycle stability (83.7 % capacity retention after 3000 cycles at 10 C). This study demonstrates a low-cost, ultra-stable, and high-rate cathode material prepared by simple mechanical activation for sodium-ion batteries which has application prospects for large-scale production.

Electrochemical Study of NaFePO4 Cathode Material in Aqueous Sodium-ion Electrolyte

Na2Fe(SO4)(2): an anhydrous 3.6 V, low-cost and good-safety cathode for a rechargeable sodium-ion battery

Activating the Inert Na1 Sites in Na<sub>2</sub>FePO<sub>4</sub>F Toward High Performance Sodium Storage

Synthesis and electrochemical studies of NaCoPO4 as an efficient cathode material using natural deep eutectic solvents for aqueous rechargeable sodium-ion batteries

Unlocking Fast and Highly Reversible Sodium Storage in Fe-Based Mixed Polyanion Cathodes for Low-Cost and High-Performance Sodium-Ion Batteries

Electrochemical Performance of NaFeFe(CN)6Prepared by Solid Reaction for Sodium Ion Batteries

Improved sodium storage properties NaFePO4/C as cathode material for sodium-ion batteries

NASICON-structured Na3Fe2PO4(SO4)2: a potential cathode material for rechargeable sodium-ion batteries

Rapid mechanochemical synthesis of high-performance Na4Fe2.94Al0.04(PO4)2(P2O7)/C cathode material for sodium-ion storage

Sustainable synthesis of Ni, Mn co-doped FePO4@C cathode material for Na-ion batteries

A New Polyanion Na3fe2(Po4)P2o7 Cathode With High Electrochemical Performance For Sodium-Ion Batteries

Synthesis of NaFePO4 by Spray Drying-Low Temperature Sintering and Corresponding Electrochemical Performance

Synthesis and characterization of a crystalline Na 4 Fe 3 (PO 4 ) 2 (P 2 O 7 ) cathode material for sodium-ion batteries

Highly Stable Na3Fe2(PO4)3@Hard Carbon Sodium-Ion Full Cell for Low-Cost Energy Storage

Monoclinic Phase Na3Fe2(PO4)3: Synthesis, Structure, and Electrochemical Performance as Cathode Material in Sodium-Ion Batteries

A New Polyanion Na 3 Fe 2 (PO 4 )P 2 O 7 Cathode with High Electrochemical Performance for Sodium-Ion Batteries

A High Capacity, Good Safety and Low Cost Na2FeSiO4-Based Cathode for Rechargeable Sodium-Ion Battery.

Detailed investigation of Na 2.24 FePO 4 CO 3 as a cathode material for Na-ion batteries

Eutectic Synthesis of the P2-Type NaxFe1/2Mn1/2O2 Cathode with Improved Cell Design for Sodium-Ion Batteries.

Solid-State Synthesis of Na4Fe3(PO4)2P2O7/C by Ti-Doping with Promoted Structural Reversibility for Long-Cycling Sodium-Ion Batteries.

Preparation and Electrochemical Performance of Porous alpha-Fe2O3 Nanospheres Anode Materials for Na-Ion Batteries