Abstract:This paper presents an experimental and theoretical study of surface generation in the ultra-precision grinding of hard and brittle materials. The study takes into account the material properties, the relative vibration between the grinding wheel and the workpiece, the machining parameters and the phase shift of the grinding process. The Taguchi approach is employed to study the influence of machining parameters on the surface quality and shows that the feed speed and rotational speed of the workpiece are key factors. Experiments have been conducted to study individual variables, and the results further show that the feed rate and the cross-feed distance have a significant effect on surface generation. It is found that the spirals around the central area of the workpiece are the primary mechanism for surface generation, which originates from the synchronous relative tool-work vibration. The integral part of the ratio of the rotational speed of the grinding wheel to rotational speed of the workpiece determines the number of spirals and its fractional part controls the spiral geometry. A theoretical model for predicting the single spiral generation has been developed to explain the accumulation of the phase shift and the geometry. The changeable feed speed near the end of grinding is also modelled, revealing the approximate straight lines around one circle in the central region. The simulated results indicate that the theoretical models and the ground surfaces are in close agreement. The scallop-height model is developed to calculate the influence of phase shift on surface quality, and it is found that the phase shift near the medium value can effectively improve surface quality. Finally, a comparison of different surface generation mechanisms in grinding mould steel, tungsten carbide (WC) and reaction bonded silicon carbide (RB-SiC) is made. It is interesting to note that the Spanzipfel effect contributes to the surface generation not only on ductile materials such as mould steel but also on brittle materials such as WC and RB-SiC. The Spanzipfel effect is the most significant in grinding mould steel. For WC and RB-SiC, the ground surface contains both a ductile region and a brittle region in the form of micro-fractures.

Nanostructured grinding wheels for ultra-precision engineering applications

Numerical Investigation of the Evolution of Grit Fracture and Its Impact on Cutting Performance in Single Grit Grinding

Studies on the Surface Quality of the Unsteady-State Grinding Technique

Nano-Precision Synergistic Finishing Process Integrated ELID-Grinding and MRF

Ultra Precision Grinding of Spherical Convex Surfaces on Combination Brittle Materials Using Resin and Metal Bond Cup Wheels

Precision Grinding of Binderless Ultrafine Tungsten Carbide (WC) Microstructured Surfaces

Selection of Abrasive Materials for Manufacturing Grinding Wheels

The mechanisms of high-efficiency grinding for micro/meso-structural arrays on ceramic moulds through an innovative wheel truing technology

Ultra-precision Machining of Hard and Brittle Materials with Coarse-Grained Grinding Wheels

The ultra-precision Ud-lap grinding of flat advanced ceramics

Alumina abrasive wheel wear in ultrasonic vibration-assisted creep-feed grinding of Inconel 718 nickel-based superalloy

Precision Grinding of a Microstructured Surface on Hard and Brittle Materials by a Microstructured Coarse-Grained Diamond Grinding Wheel

Grindability studies of thermomechanically processed advanced high strength steel using sol-gel and fused alumina grain-based grinding wheels

Micro/Nano Indentation and Single Grit Diamond Grinding Mechanism on Ultra Pure Fused Silica

Novel surface characteristics observed during grinding of polycrystalline diamond

Optimal Design and Performance Evaluation of Grinding Wheels with Triply Periodic Minimal Surface Lattice Structure

On the Grinding Performance of Alumina Wheels in Ultrasonic Vibration–assisted Grinding of Hardened GCr15 Steel

Self-sharpening property of porous metal-bonded aggregated cBN wheels during the grinding of Ti–6Al–4V alloys

Micro-grooving of brittle materials using textured diamond grinding wheels shaped by an integrated nanosecond laser system

An experimental and theoretical analysis of surface generation in the ultra-precision grinding of hard and brittle materials

Wear Behavior of Grain Cutting Edge in Ultrasonic Assisted Grinding Using Mini-Size Wheel.