Abstract:Resource characterization and modelling are important in exploration wherein cores of rock are extracted from the surface. Such cores not only help to assess the quantity and quality of the mineral or ore but also provide means to establish an excavation and ground control regime for different types of mining. Prediction of coring rate assumes critical importance for planning the coal mines which have fragile nature of ground posing challenges in strata control and excavation performance. Coring rate or associated rock factors characterize the rockmass to help in this regard. In line with the above need, the geological and machine performance data of two representative boreholes drilled at 90° and 80° in a complex coal bearing strata were collected covering drill machine variables, penetration rates and physico-mechanical properties of the rock cores in laboratory. The penetration rate showed significant deviation up to a depth of 250 m from the surface in both the holes. The variation in penetration rate was 28% in basalt and 38% in mudstone, 16% in sandy shale with coal, 10% in sandy shale and − 2% in medium to coarse grained sandstone. In order to model the penetration rate, a rock designation factor was devised in terms of the depth, tensile strength and density of the rockmass. The rock designation factor along with other machine variables were analyzed initially using PCA enabled Gaussian progression method which helped in model refinement and selection of best variables. Subsequently, response surface analysis of selected variables viz., rock designation factor, torque, drill fluid pressure and RPM, using multivariate non-linear ANOVA with backpropagation method to develop a penetration rate model. Drill angle and rock type were retained as categorial factors. The model thus devised was evaluated using various techniques and resulted in RMSE of 8.1, MAE of 5.59, MSE of 65.61 with predicted R2 of 0.927. The intercepts for different rocks analyzed were thus enumerated. The model developed can be used for defining penetration rates for the type of drill investigated. Explicit surface response with variations in different variables could thus be defined along with the relative sensitivity of the variables entering into the interaction with perturbation method. Also, a variation of 50 mm/min in penetration rates in 90° and 80°drilling is accounted by the model. The penetration rate prediction model is sensitive to the rock designation factor, RPM, drill fluid pressure, angle of drilling and torque in decreasing order. It is observed that the best penetration rate can be achieved at an average RPM of 436 and minimum drill fluid pressure of 6 kg/cm2, indicating that higher drill fluid pressures may not favor higher penetration rates.Article highlightsData of two holes drilled at 90° and 80° upto a depth of 326 m in complex Gondwana Region were investigated for effect of machine and rock properties on penetration rate.Exploratory data analysis revealed significant effect of depth on penetration rate upto 250 m. A Rock Designation Factor comprising of depth of rock, density and tensile strength was developed to address different modelling issues.Multivariate analysis of the data along with principal component analysis was used to select the variables for modelling. Response surface analysis, was used to develop a multivariate model for prediction of penetration rate that helped to identify the sensitivity of the variables.

Drillability studies on the rotary blasthole drilling of lignite overburden series

Investigation of the Effect of Drill Bit Rotation Speed on Sustainable Drilling

Investigation of explosibility characteristics of some Turkish lignite coal dusts

Drilling and blasting designs for parallel hole cut and V-cut method in excavation of underground coal mine galleries

An experimental investigation into the borehole drilling and strata characteristics

Performance prediction modeling of standard penetration blow count of clayey soils by two non-linear tools

Rock mass classification for estimating the drilling rate in a surface mine using rock mass drillability index

Evaluating the maximum rate of penetration for drilling borehole in soft coal seam

Estimation of Optimal Drilling Efficiency and Rock Strength by Using Controllable Drilling Parameters in Rotary Non-Percussive Drilling

Evaluating the Relationships Between NTNU/SINTEF Drillability Indices with Index Properties and Petrographic Data of Hard Igneous Rocks

Performance analysis of drilling machines based on rock properties and machine's specifications

Performance Evaluation of Button Bits in Coal Measure Rocks by Using Multiple Regression Analyses

Investigations on the influence of rock and machine characteristics on coring rates in vertical and mildly inclined exploration drilling in complex coal bearing rock formation

A novel Hybrid XGBoost Methodology in Predicting Penetration Rate of Rotary Based on Rock-Mass and Material Properties

Dynamic Mechanical Behaviors and Failure Mechanism of Lignite under SHPB Compression Test

Evaluating the influence of engineering geological parameters on TBM performance during grinding process in limestone strata

Theoretical and experimental studies on relationship between working parameters of cone drill and rock strengths

Evaluation and Simulation Study of Rock Drillability Grades in the Tazhong-Tabei Block

Seam Modelling and Reserve Calculation for Lignite Field in Adana-Tufanbeyli (Turkey)

Real-time rock strength determination based on rock drillability index and drilling specific energy: an experimental study