Abstract:It is known that Copper's (Cu) electrical conductivity makes it a desirable material for use in industry. Due to poor properties such as hardness, thermal expansion, and corrosion resistance, its applications are limited. This manuscript solves these problems while maintaining no breakdown in electrical conductivity. In this study, high-strength ceramics (SiC nanoparticles and graphene nanosheets) were used as reinforcements in the manufacture of Cu-based hybrid nanocomposites using powder metallurgy technique. X-ray diffraction analysis (XRD) was used to investigate phase composition and crystal size of the milled powders. Transmission electron microscopy (TEM) and field emission scanning electron microscopy (FESEM), respectively examined the microstructure of the prepared powder powders and sintered nanocomposites. Then, various properties of the sintered samples are measured, including physical, electrical and thermal properties and wear resistance. The obtained XRD technique and TEM images showed decreases in the crystal and particle size of milled samples reaching up to 14.08 and 28.30 nm, respectively for the sample contained 8 vol. % SiC + 0.8 vol. % graphene (SG8). A surprising improvement in the mechanical properties of up to 809.15, 341.84 MPa and 336.56 GPa for microhardness, strength and longitudinal modulus for the sample containing the highest reinforcements, achieving an improvement of up to 122, 61.37 and 41 percent compared to the Cu matrix. Moreover, there was a noticeable improvement in the coefficient of thermal expansion (CTE) and wear rate values of the samples by increasing the percentages of hybrid reinforcements in the examined sintered nanocomposite samples. The Sample SG8 recorded the lowest value, decreasing by about 50.2 and 76.5% compared to the SG1 sample. Finally, adding reinforcements to the Cu matrix had a negative effect on the relative density and electrical conductivity, and the lowest values was 92.94% and8.59 × 10 6 S/m, respectively for the SG sample.

Realization of high thermal conductivity and tunable thermal expansion in the ScF3@Cu core-shell composites

Achieving High Performances of Ultra-Low Thermal Expansion and High Thermal Conductivity in 0.5PbTiO 3 -0.5(Bi 0.9 La 0.1 )FeO 3 @Cu Core–Shell Composite

Adjustable Thermal Expansion in La( Fe, Si)(13)-based Conductive Composites by High-Pressure Synthesis

Excellent thermoelectric properties and stability realized in copper sulfides based composites via complex nanostructuring

Balance thermal conductivity and thermal expansion in RGO/Cu composites through alignment engineering

Synergistic enhancing effect of tungsten-copper coated graphite flakes and aluminum nitride nanoparticles on microstructure, mechanical and thermal properties of copper matrix composites

Improving the incompatibility between electromagnetic and thermal properties of CNF/Co composites via constructing 3D interconnected frameworks, double hot carriers, and multiple losses

Effects of Zr-Cu Alloy Powder on Microstructure and Properties of Cu Matrix Composite with Highly-Aligned Flake Graphite

High thermal and mechanical properties of carbon fiber network reinforced copper matrix composites achieved by configuration design and interface engineering

Sintering pressure effect on the performances of near-zero thermal expansion xLFCS/Cu metal matrix composites

Ultralow Thermal Conductivity and Negative Thermal Expansion of CuSCN

Fabrication, mechanical and thermal properties of tungsten-copper coated graphite flakes reinforced copper matrix composites

Evaluation of tribo-mechanical measurements and thermal expansion of Cu-based nanocomposites reinforced by high strength hybrid ceramics

Enhanced performance of thermoelectric nanocomposites based on Cu12Sb4S13 tetrahedrite

Synergetic effect enabling high thermal conductivity in Cu/diamond composite

Enhanced Thermoelectric Properties Of Cu3sbse3-Based Composites With Inclusion Phases

Core-shell Cu@Al2O3 fillers for enhancing thermal conductivity and retaining electrical insulation of epoxy composites

Thermal and Electrical Properties of Feni/Cu Composites

Fabrication of a Cu/TiNi Composite with High Air-Tightness and Low Thermal Expansion

Microstructure and thermal properties of copper matrix composites reinforced by 3D carbon fiber networks

Microstructure and Properties of W Cu Composites with Low Copper Content at Different Sintering Temperatures