Abstract:Summary In preferentially oil-wet porous media, laboratory waterflooding experiments are prone to capillary end effects. The wetting phase (oil) will tend to accumulate at the outlet where the capillary pressure is zero and leave a highly remaining-oil saturation at steady state (defined by a stable pressure drop and a zero oil-production rate) compared to the residual-oil saturation. Andersen et al. (2017c) derived analytical solutions describing how the capillary pressure and relative permeability of water (the injected phase) could be determined on the basis of pressure drop and average saturation at steady states obtained at different water-injection rates. Plotting these values against inverse rate reveals linear trends at high rates, with slopes and intercepts that directly quantify the saturation functions in the range of negative capillary pressures. The method is similar to the Gupta and Maloney (2016) intercept theory but quantifies entire functions rather than a single point and provides the trends also at low rates, thus using all the information. Our aim is to demonstrate how pressure drop and oil production at steady state for different water-injection rates can be used to derive relative permeability and capillary pressure from waterflooding. This is done in three ways. First, synthetic transient waterflooding tests are generated (using a core-scale simulator), applying the same saturation-function correlations as assumed in the analytical solution. Then, more-general correlations are assumed when generating the synthetic data. This is to test the robustness of the analytical solution in producing functions similar to the “true” ones. Finally, we perform a waterflooding experiment in the laboratory on a high-permeability (3 darcies) Bentheimer sandstone core, altered to an oil-wet state. Forced imbibition was started at a rate of 0.4 pore volumes (PV) per day, which was increased stepwise after approaching a steady state. Twelve rates were applied, differing overall by a factor of ≈1,000 to yield states governed by capillary forces and advective forces. The results were interpreted using both full history matching of the transient data and matching of the steady-state data with the analytical solution. The experimental procedure and model demonstrate that only water relative permeability and capillary pressure determine the steady state during waterflooding, and hence can be estimated accurately. The analytical solution could simultaneously match the trends and magnitude of a steady-state pressure drop and production with injection rate to give an estimation of the saturation functions. The estimated saturation functions from the analytical solution agreed well with the estimates from full history matching.

Effect of Pressure Gradient and Initial Water Saturation on Water Injection in Water-Wet and Mixed-Wet Fractured Porous Media

Effect of Pressure Gradient and Initial Water Saturation on Water Injection in Water-Wet and Mixed-Wet Fractured Porous Media

Effect of injection rate, initial water saturation and gravity on water injection in slightly water-wet fractured porous media

A New Waterflood Initialization Protocol With Wettability Alteration for Pore-Scale Multiphase Flow Experiments

Simulation Interpretation of Capillary Pressure and Relative Permeability From Laboratory Waterflooding Experiments in Preferentially Oil-Wet Porous Media

Imaging and Measurement of Pore‐Scale Interfacial Curvature to Determine Capillary Pressure Simultaneously with Relative Permeability

Dynamics of Water Injection in an Oil-Wet Reservoir Rock at Subsurface Conditions: Invasion Patterns and Pore-Filling Events

Effects of Clay Minerals and External Pressures on Imbibition in Shales

Variations in Hydraulic Properties of Sendimentary Rocks Induced by Fluid Injection: the Effect of Water Pressure

Water-Induced Damage in Microporous Carbonate Rock by Low-Pressure Injection Test

Wettability Effects on Capillary Pressure, Relative Permeability, and Irredcucible Saturation Using Porous Plate

Pore-scale Analysis of CO2-brine Displacement in Berea Sandstone and Its Implications to CO2 Injectivity

Effect of Fluid Pressure and Pore Structure on Tight Sand Gas Saturation—Evidence from Micro-CT Simulation Experiment

Experimental study of hydraulic fracture initiation and propagation in deep shale with different injection methods

Experimental and Simulation Based Interpretation of Characteristic Behavior During Forced and Spontaneous Imbibition in Strongly Water-Wet Sandstones

Water-Gas Imbibition Relative Permeability: Literature Review, Direct versus Indirect Methods and Experimental Recommendations

Experimental Investigation on the Spontaneous Imbibition Characteristics of Shale under the Combined Action of CO 2 and Water

Effect of reservoir composition and structure on spontaneous imbibition: a case study of Shahejie Formation shale in Zhanhua Sag, Bohai Bay Basin

Effects of Injection Pressure and Duration on Alternate High-Pressure Water-Gas Sequestration of Coalbed Methane

The effects of initial water saturation on retrograde condensation in natural porous media: An in situ experimental investigation of three-phase displacements

Experimental Evaluation of Blockage Resistance and Position Caused by Microparticle Migration in Water Injection Wells