Abstract:Combustion system development in power generation is discussed ranging from the pre-environmental era in which the objectives were complete combustion with a minimum of excess air and the capability of scale up to increased boiler unit performances, through the environmental era (1970–), in which reduction of combustion generated pollution was gaining increasing importance, to the present and near future in which a combination of clean combustion and high thermodynamic efficiency is considered to be necessary to satisfy demands for CO2 emissions mitigation.From the 1970s on, attention has increasingly turned towards emission control technologies for the reduction of oxides of nitrogen and sulfur, the so-called acid rain precursors. By a better understanding of the NOx formation and destruction mechanisms in flames, it has become possible to reduce significantly their emissions via combustion process modifications, e.g. by maintaining sequentially fuel-rich and fuel-lean combustion zones in a burner flame or in the combustion chamber, or by injecting a hydrocarbon rich fuel into the NOx bearing combustion products of a primary fuel such as coal.Sulfur capture in the combustion process proved to be more difficult because calcium sulfate, the reaction product of SO2 and additive lime, is unstable at the high temperature of pulverized coal combustion. It is possible to retain sulfur by the application of fluidized combustion in which coal burns at much reduced combustion temperatures. Fluidized bed combustion is, however, primarily intended for the utilization of low grade, low volatile coals in smaller capacity units, which leaves the task of sulfur capture for the majority of coal fired boilers to flue gas desulfurization.During the last decade, several new factors emerged which influenced the development of combustion for power generation. CO2 emission control is gaining increasing acceptance as a result of the international greenhouse gas debate. This is adding the task of raising the thermodynamic efficiency of the power generating cycle to the existing demands for reduced pollutant emission. Reassessments of the long-term availability of natural gas, and the development of low NOx and highly efficient gas turbine–steam combined cycles made this mode of power generation greatly attractive also for base load operation.However, the real prize and challenge of power generation R&D remains to be the development of highly efficient and clean coal-fired systems. The most promising of these include pulverized coal combustion in a supercritical steam boiler, pressurized fluid bed combustion without or with topping combustion, air heater gas turbine-steam combined cycle, and integrated gasification combined cycle. In the longer term, catalytic combustion in gas turbines and coal gasification-fuel cell systems hold out promise for even lower emissions and higher thermodynamic cycle efficiency. The present state of these advanced power-generating cycles together with their potential for application in the near future is discussed, and the key role of combustion science and technology as a guide in their continuing development highlighted.

Evolution of Westinghouse Heavy-Duty Power Generation and Industrial Combustion Turbines

Development of the Heavy-Duty Gas Turbine

System Status of the Water-Cooled Gas Turbine for the High Temperature Turbine Technology Program

Siemens Westinghouse Advanced Turbine Systems Program Final Summary

Baseline Airfoil Cooling Designs for a 5-10 MW Combined Heat and Power Turbine Application

Recent developments in gas turbine materials and technology and their implications for syngas firing

Status and Development Trend of the Heavy Duty Gas Turbine

Current Status and Prospects of High-Speed Direct-Drive Power Generation Technology

Combustion technology developments in power generation in response to environmental challenges

Evolution of engines: From steam to turbojet

Green Engine Technologies for Small Gas Turbines

Materials for Gas Turbine Engines: Present Status, Future Trends and Indigenous Efforts

Model Development and Simulation of Transient Behavior of Heavy Duty Gas Turbines

Trends in Wind Turbine Generator Systems

Gas Turbine Engine Health Management: Past, Present, and Future Trends

Current Status and Prospects of Gas Turbine Technology Application

Advanced Materials and Cooling Technologies for High Thermal Load Components in Ultra Supercritical Steam Turbine

Challenges for Developing and Marketing a Brayton-Cycle Based Power Genset Gas-Turbine Using Supercritical CO2 and a Compressor Design for Simple Recuperated Cycle

A Review on the Evolution of Darrieus Vertical Axis Wind Turbine: Small Wind Turbines

A High-Speed, High-Temperature, Micro-Cantilever Steam Turbine for Hot Syngas Compression in Small-Scale Combined Heat and Power

Enhancing the Energy Performance of a Gas Turbine: Component of a High-Efficiency Cogeneration Plant