Abstract:The trend for higher overall pressure ratios means that turbine entry temperatures are continually increasing. Furthermore, the development of lean, low-emission combustion systems reduces the availability of cooling air and is accompanied by new problems at the combustor/turbine interface. For example, the exit temperature traverse differs from that found in traditional rich-burn combustors with increased swirl and a much flatter profile. Effectively cooling the turbine components is becoming increasingly difficult. One solution is to employ cooled cooling air (CCA) where some of the compressor efflux is diverted for additional cooling in a heat exchanger located in the by-pass duct. An example CCA system is presented which includes an off-take within the dump cavity and the addition of radial struts within the pre-diffuser through which the cooled air is returned to the engine core. This paper addresses the impact this CCA system has on the combustion system external aerodynamics. This included the development of a fully annular, isothermal test facility which incorporated a bespoke 1.5 stage axial compressor, engine relevant outlet guide vanes, pre-diffuser and combustor geometry. A datum aerodynamic performance was established for a non-CCA configuration with a clean, un-strutted pre diffuser. Results for this baseline CCA system demonstrated that inclusion of a bleed in the dump cavity had limited effect on the overall flow field. However, the inclusion of struts within the pre-diffuser caused a reduction in area ratio and a notable increase in system loss. Consequently an alternative pre-diffuser was designed (using CFD) with the aim of increasing the area ratio back to that of the un-strutted datum. A so-called hybrid diffuser was designed in which the CCA bleed was moved to the pre-diffuser outer wall. The bleed was then used to re-energize the boundary layer, preventing flow separation, enabling the area ratio to be increased close to the datum value. The mechanisms of the hybrid diffuser are complex; the geometry of the off-take and its location with respect to the OGV and strut leading edge were seen to be critical. Experimental evaluation of the final design demonstrated the effective operation the hybrid diffuser with the result that the system loss returned to a level close to that of the datum. Only small differences were seen in the overall flow field.

CFD Modeling of a Gas Turbine Combustor From Compressor Exit to Turbine Inlet

Advanced Modeling Approaches for CFD Simulations of Coal Combustion and Gasification

CFD Simulation of Combustion in Gas Turbine Engine

Computational Study of a Swirl Stabilized Flame in a Gas Turbine Combustor

Experimental and Numerical Investigation of the Non-Reacting Flow in a High-Fidelity Heavy-Duty Gas Turbine DLN Combustor

Large Eddy Simulations of Turbulent Combustion of Kerosene-Air in a Dual Swirl Gas Turbine Model Combustor at High Pressures

Two-dimensional coal combustion modeling of CFB

Influence of the turbulence model on the numerical predictions of cold turbulent flow in a heavy-duty gas turbine DLN combustor

Design and Numerical Simulation of a Micro-Gas Turbine Combustor

Bleed air CFD modelling in aerodynamic simulation of A heavy duty gas turbine compressor

Computational Study on Compressor-Combustor Interactions for Improved Matching of a Micro Gas Turbine

Development of 1D Model of Constant-Volume Combustor and Numerical Analysis of the Exhaust Nozzle

Large-Eddy Simulation of Reacting Flows in Industrial Gas Turbine Combustor

Combustion Modeling Of Cfb Boiler Furnace Based On An Euler-Euler Approach

Three-Dimensional Simulation of Steam Injected Gas Turbine Combustor Inner Flowfield Characteristics

Numerical Simulation Research on Three Dimensional Turbulence Flow in a Gas Turbine Combustor Burning Low Heat Value Syngas

Effect of Steam Addition on Gas Turbine Combustor Design and Performance

Development of a Throughflow-Based Simulation Tool for Preliminary Compressor Design Considering Blade Geometry in Gas Turbine Engine

Impact of a Cooled Cooling Air System on the External Aerodynamics of a Gas Turbine Combustion System

Experimental Characterization of the Spatiotemporal Dynamics of a Turbulent Flame in a Gas Turbine Model Combustor Using Computed Tomography of Chemiluminescence

Experimental Data Based Reduced Order Model for Analysis and Prediction of Flame Transition in Gas Turbine Combustors