Abstract:Mesostructured silica SBA-15 materials with different structural parameters, such as pore size, pore volume, and wall thickness, etc., were prepared by varying the postsynthesis hydrothermal treatment temperature and adding inorganic salts. The hydrothermal stabilities of these materials in steam (100% water vapor) were systematically investigated using a variety of techniques including powder X-ray diffraction, transmission electron microscopy, nitrogen sorption, and (29)Si solid-state NMR. The effect of the pore size, microporosity or mesoporosity, and wall thickness on the stability was discussed. The results show that all of the SBA-15 materials have a good hydrothermal stability under steam of 600 degrees C for at least 24 h. N(2) sorption measurements show that the Brumauer-Emmett-Teller surface area of SBA-15 materials is decreased by about 62% after treatment under steam at 600 degrees C for 24 h. The materials with thicker walls and more micropores show relatively better hydrothermal stability in steam of 600 degrees C. Interestingly, we found that the microporosity of the mesostructured silica SBA-15 is a very important factor for the hydrothermal stability. To the materials with more micropores, the recombination of Si-O-Si bonds during the high-temperature steam treatment may not cause direct destruction to the wall structure. As a result, SBA-15 materials with more micropores show better stability in pure steam of 600 degrees C. Nevertheless, these materials are easily destroyed in steam of 800 degrees C for 6 h. Two methods to effectively improve the hydrothermal stability are introduced here: one is a high-temperature treatment, and another is a carbon-propping thermal treatment. Thermal treatment at 900 degrees C can enhance the polymerization degree of Si-O-Si bonds and effectively improve the hydrothermal stability of these SBA-15 materials in 800 degrees C steam for 12 h. But, this approach will cause very serious shrinkage of the mesopores, resulting in smaller pore diameter and low surface area. A carbon-propping thermal treating method was employed to enhance the polymerization of Si-O-Si bonds and minimize the serious shrinkage of mesopores at the same time. It was demonstrated to be an effective method that can greatly improve the hydrothermal stability of SBA-15 materials in 800 degrees C steam for 12 h. Furthermore, the SBA-15 materials obtained by using the carbon-propping method possess larger pores and higher surface area after the steam treatment at 800 degrees C compared to the materials from the direct thermal treatment method after the steam treatment.

Effects of Hydrothermal Treatment and Template Removal on the Adsorption and Structural Properties of SBA-16 Mesoporous Silica

Hydrothermal stability of SBA-15 and related ordered mesoporous silicas with plugged pores

The effect of hydrothermal temperature on the properties of SBA-15 materials

Thermal and hydrothermal stability of amino-functionalized SBA-16 and promotion of hydrophobicity by silylation

A novel mesoporous silica-clay composite and its thermal and hydrothermal stabilities

Synthesis and Characterization of Small Pore Thick-Walled SBA-16 Templated by Oligomeric Surfactant with Ultra-Long Hydrophilic Chains

On the improvement of pore accessibility through post-synthesis hydrothermal treatments of spray dried SBA-15 microspheres

Synthesis of high surface area mesoporous silica SBA-15 by adjusting hydrothermal treatment time and the amount of polyvinyl alcohol

Effect of microwave irradiation on the structural, chemical, and hydrophilicity characteristics of ordered mesoporous silica SBA-15

Adsorption of Carbon Dioxide on Organically Functionalized Sba-16

Simultaneous Removal of Copolymer Template from SBA-15 in the Crystallization Process

Mesostructured Silica SBA-16 with Tailored Intrawall Porosity Part 1: Synthesis and Characterization

Effects of acid treatment on the physico-chemical and pore characteristics of halloysite

Ordered cubic mesoporous silicas with large pore sizes synthesized via high-temperature route.

Improving the Hydrothermal Stability of Mesoporous Silica SBA-15 by Pre-treatment with (Nh4)2sif6

Hybrid template directed hydrothermal synthesis of MCM-41 silicas with surface silanol and 3-chloropropyl groups

Understanding Effect of Wall Structure on the Hydrothermal Stability of Mesostructured Silica SBA-15.

Tuning Textural Properties by Changing the Morphology of SBA-15 Mesoporous Materials

Impact of porosity and surface functionalization of hard templates on the preparation of mesoporous silica microspheres

Synthesis of hydrothermally stable, hierarchically mesoporous aluminosilicate Al-SBA-1 and their catalytic properties

Effect of silica/alumina ratio and structure-directing agent on the physical and chemical properties of SAPO-34