Abstract:For further efficiency improvement in kesterite-type Cu2ZnSn(S,Se)4 (CZTSSe) solar cells, it is essential to address the carrier recombination issue at the back electrode interface (BEI) caused by the undesirable built-in potential orientation toward an absorber as an n-MoSe2 interfacial layer formed. In this regard, back surface field (BSF) incorporation, i.e., field-effect passivation, shows promise for dealing with this issue due to its positive effect in decreasing recombination at the BEI. In this study, the BSF was realized with the p-type conduction transition in interfacial layer MoSe2 by incorporating Nb into the back electrode. The BSF width can be tuned via modulating the carrier concentration of the absorber, which has been demonstrated by capacitance–voltage characterization. A beyond 7% efficiency BSF-applied CZTSSe solar cell is prepared, and the effects of a tunable BSF and the mechanism underpinning device performance improvement have been investigated in detail. The wider BSF distribution in the absorber induces a decrease in reverse saturation current density (J0) due to the stronger BSF effect in suppressing BEI recombination. As a result, an accompanying increase in open-circuit voltage (VOC) and short-circuit current density (JSC) is achieved as compared to the BSF-free case. This study offers an alternative strategy to address the BEI recombination issue and also broadens the interface passivation research scope of potentially competitive kesterite solar cells.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c10561?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c10561</a>.EDS spectrum of a Mo:Nb film grown on the SLG substrate and statistical histograms of the absorber grain size distribution from the SEM images in <a class="internalNav" href="#fig5">Figure </a><a class="internalNav" href="#fig5">5</a>a,b; composition ratios in CZTS precursor solution; the compositions of MoSe2 and MoSe2:Nb films measured via EDS and XPS and those of CZTSSe films prepared on the SLG substrate measured by EDS (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c10561/suppl_file/am0c10561_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Performance Analysis for SnS- and Sn2S3-Based Back Surface Field CZTSSe Solar Cell: A Simulation Study

Simulation and numerical modeling of high‐efficiency CZTS solar cells with a BSF layer

Analysis Of SnS2 Buffer Layer And SnS Back Surface Layer Based CZTS Solar Cells Using SCAPS

Investigation of Back Surface Field Layer for High Efficiency Ultrathin In2S3 based CIGS Solar Cell

Performance evaluation of WS2 as buffer and Sb2S3 as hole transport layer in CZTS solar cell by numerical simulation

Modulation of Field-Effect Passivation at the Back Electrode Interface Enabling Efficient Kesterite-Type Cu 2 ZnSn(S,Se) 4 Thin-Film Solar Cells

Combating open circuit voltage loss in Sb2Se3 solar cell with an application of SnS as a back surface field layer

Design and simulation of a new kesterite solar cell structure with and without a perovskite Back Surface Field layer to exceed 32% efficiency

Modulation of Field-Effect Passivation at the Back Electrode Interface Enabling Efficient Kesterite-Type Cu2ZnSn(S,Se)4 Thin-Film Solar Cells.

Thin-film CZTSSe solar cells efficiency improvement through BSF SnS layer and concentrator applications

Self-Organized Back Surface Field to Improve the Performance of Cu2ZnSn(S,Se)4 Solar Cells by Applying P-Type MoSe2:Nb to the Back Electrode Interface

Impact on generation and recombination rate in Cu2ZnSnS4 (CZTS) solar cell for Ag2S and In2Se3 buffer layers with CuSbS2 back surface field layer

A qualitative Design and optimization of CIGS-based Solar Cells with Sn2S3 Back Surface Field: A plan for achieving 21.83 % efficiency

CHTS/Zn2P3-based solar cells with enhanced efficiency through ETL engineering: A numerical study

Analysis of Lead Free CsSnBr3 based Perovskite Solar cells utilizing Numerical Modeling

Elucidating the Potential Strategies for Performance Improvement of CBTSSe‐Based Solar Cells: A Pathway Toward 20% Efficiency

N‐Type Surface Design for p‐Type CZTSSe Thin Film to Attain High Efficiency

Simulation studies of CZT(S,Se) single and tandem junction solar cells towards possibilities for higher efficiencies up to 22%

Numerical modeling of CuSbSe2-based dual-heterojunction thin film solar cell with CGS back surface layer

Numerical Simulation of SnS/CZTSSe Heterojunction Solar Cells

Optimizing efficiency in CHTS-based solar cells through controlling tin content of (Zn, Sn)O buffer layer and integration of SnS as back surface field layer: a numerical approach