Abstract:Poly(vinylidene difluoride) (PVDF) has become the polymer matrix of choice for fabrication of wearable electronics and physiological monitoring devices. Despite possessing a high piezoelectric constant, additives are required to increase the charge transfer from PVDF matrix to connected signal readout units. Many of these additives also stabilize the β-phase of PVDF, which is associated with highest piezoelectric coefficients. However, most of the additives used are often brittle ceramic-phase materials resulting in decreased flexibility of the devices and offsetting the gain in β-phase content. Intrinsically conducting polymers (ICP), on the other hand, are ideal candidates to improve the device-related properties of PVDF, due to their higher flexibility than ceramic fillers as well as ability to form conducting network in PVDF membranes. This work reports the performance and device feasibility of PVDF-polycarbazole (PCZ) electrospun nanofiber membranes. A higher β-phase was observed by FTIR spectroscopy in PVDF/PCZ compared to other PVDF phases. Moreover, a higher open-circuit potential was recorded over PVDF/polyaniline composites, which were studied for comparison. The addition of PCZ reduced the flexibility of pure PVDF nanofibers by 20% only. Besides, the work investigated the bacterial biofouling and cell compatibility of the matrix, as essential properties to examine any putative medical device application. PVDF/PCZ membranes were then used to develop a nanogenerator, which was capable of instantly lighting an entire LED array employing the rectified output power, and charged up a 2.2 μF capacitors using a bridge rectifier through a vertical compressive force applied periodically. Finally, the nanogenerator demonstrated electrical energy harvesting from movements of various parts of the human body, such as toe and heel movement and wrist bending. In conclusion, PCZ can be considered as an attractive, biocompatible, and anti-biofouling conducting polymer for electrical actuation and flexible electronic device applications.

Piezoelectric Nanogenerator Based on Electrospun Cellulose Acetate/Nanocellulose Crystal Composite Membranes for Energy Harvesting Application

Piezoelectric Nanogenerator Based on a Flexible Carbon-Fiber/zno–znse Bilayer Structure Wire

A Self-Supported Structure Hybrid Triboelectric/piezoelectric Nanogenerator for Bio-Mechanical Energy Harvesting and Pressure Sensing

Flexible Piezoelectric Nanogenerator Based on Cellulose Nanofibril/MXene Composite Aerogels for Low-Frequency Energy Harvesting

Piezoelectric nanogenerators from sustainable biowaste source: Power harvesting and respiratory monitoring with electrospun crab shell powder-poly(vinylidene fluoride) composite nanofibers

Interface-engineered composite nanofibers for boosting piezoelectric outputs of polymeric nanogenerators

Carbon Nanotubes Doped Cellulose Nanocomposite Film for High Current Flexible Piezoelectric Nanogenerators

A high performance nanocellulose-PVDF based piezoelectric nanogenerator based on the highly active CNF@ZnO via electrospinning technology

High value-added development of waste cellulose peels for bio-piezoelectric membrane in nanogenerator-derived self-powered sensor

Porous Cellulose Composite Aerogel Films with Super Piezoelectric Properties for Energy Harvesting

A Piezoelectric Generator Based on PVDF/GO Nanofiber Membrane

Hybrid Piezoelectric/Triboelectric Wearable Nanogenerator Based on Stretchable PVDF-PDMS Composite Films

Mesoporous Piezoelectric Polymer Composite Films with Tunable Mechanical Modulus for Harvesting Energy from Liquid Pressure Fluctuation

Physico-chemical and piezoelectric characterization of electroactive nanofabrics based on functionalized graphene/talc nanolayers/PVDF for energy harvesting

High sensitivity flexible piezoelectric nanogenerator based on multi‐layer piezoelectric composite fiber for human motion energy harvesting

Development of a flexible piezoelectric and triboelectric energy harvester with piezo capacitive sensing ability from barium tungstate nanorod-dispersed PVDF nanofabrics

Enhanced Flexible Piezoelectric Nanogenerators Using Ethanol-Exfoliated g-C3N4/PVDF Composites via 3D Printing for Self-Powered Applications

Wave-Shaped Piezoelectric Nanofiber Membrane Nanogenerator for Acoustic Detection and Recognition

Piezoelectric Energy Harvesting Using Flexible Self-Poled Electroactive Nanofabrics Based on PVDF/ZnO-Decorated SWCNT Nanocomposites

Flexible Nanogenerator from Electrospun PVDF-Polycarbazole Nanofiber Membranes for Human Motion Energy-Harvesting Device Applications

Wearable Electrospun Piezoelectric Mats Based on a PVDF Nanofiber–ZnO@ZnS Core–Shell Nanoparticles Composite for Power Generation