Abstract:Abstract In deep underground mining, achieving stable support for roadways along with long service life is critical and the complex geological environment at such depths frequently presents a major challenge. Owing to the coupling action of multiple factors such as deep high stress, adjacent faults, cross-layer design, weak lithology, broken surrounding rock, variable cross-sections, wide sections up to 9.9 m, and clusters of nearby chambers, there was severe deformation and breakdown in the No. 10 intersection of the roadway of large-scale variable cross-section at the − 760 m level in the Nanfeng working area of the Wuyang Coal Mine. As there are insufficient examples in engineering methods pertaining to the geological environment described above, the numerical calculation model was oversimplified and support theory underdeveloped; therefore, it is imperative to develop an effective support system for the stability and sustenance of deep roadways. In this study, a quantitative analysis of the geological environment of the roadway through field observations, borehole peeking, and ground stress testing is carried out to establish the FLAC 3D variable cross-section crossing roadway model. This model is combined with the strain softening constitutive (surrounding rock) and Mohr-Coulomb constitutive (other deep rock formations) models to construct a compression arch mechanical model for deep soft rock, based on the quadratic parabolic Mohr criterion. An integrated control technology of bolting and grouting that is mainly composed of a high-strength hollow grouting cable bolt equipped with modified cement grouting materials and a high-elongation cable bolt is developed by analyzing the strengthening properties of the surrounding rock before and after bolting, based on the Heok-Brown criterion. As a result of on-site practice, the following conclusions are drawn: (1) The plastic zone of the roof of the cross roadway is approximately 6 m deep in this environment, the tectonic stress is nearly 30 MPa, and the surrounding rock is severely fractured. (2) The deformation of the roadway progressively increases from small to large cross-sections, almost doubling at the largest cross-section. The plastic zone is concentrated at the top plate and shoulder and decreases progressively from the two sides to the bottom corner. The range of stress concentration at the sides of the intersection roadway close to the passageway is wider and higher. (3) The 7 m-thick reinforced compression arch constructed under the strengthening support scheme has a bearing capacity enhanced by 1.8 to 2.3 times and increase in thickness of the bearing structure by 1.76 times as compared to the original scheme. (4) The increase in the mechanical parameters c and φ of the surrounding rock after anchoring causes a significant increase in σ c and σ t ; the pulling force of the cable bolt beneath the new grouting material is more than twice that of ordinary cement grout, and according to the test, the supporting stress field shows that the 7.24 m surrounding rock is compacted and strengthened in addition to providing a strong foundation for the bolt (cable). On-site monitoring shows that the 60-day convergence is less than 30 mm, indicating that the stability control of the roadway is successful.

A study on the geometric effects of a concrete filling body in remaining roadways with fully mechanised caving

Study on the Bearing Characteristics and Application of the Filling Body in Original Roadway Filling and Nonpillar Driving

Experimental study on combined load-bearing instability of filling body and roadway surrounding rock in original roadway filling without coal pillar excavation

Study on the Bearing Mechanism and Stability of Surrounding Rock in Original Roadway Filling and Nonpillar Tunneling

Failure Analysis of Intersections of Large-Scale Variable Cross-Section Roadways in Deep Soft Rock and Study of Integrated Control Technology of Bolting and Grouting

Asymmetric Deformation Mechanism of Roadway with Continuous Mining and Continuous Backfilling

Effects of width-height ratio and roof-floor strength on the mechanical characteristics of cemented gangue backfill pier-column

Deformation mechanism and control technology of gob-side roadway with continuous mining and continuous backfilling: a case study

Failure Mechanisms and Reinforcement Support of Soft Rock Roadway in Deep Extra-Thick Coal Seam: A Case Study

Failure mechanisms and reinforcement support of roadway in deep coal seam: A case study

Research and Development of Steel Fiber Reinforced Concrete Filling Material and Its Application in Gob-Side Entry Retaining Technology in Deep Mines

Filling wall mechanical analysis of gob-side entry retaining with composite roof

Investigation on application of filling mining technology pass through abandoned roadway of reclaimed working face

Deformation failure mechanism and concrete-filled steel tubular support control technology of deep high-stress fractured roadway

Deformation mechanism and control technology of gob-side entry retaining with roadside backfilling: a numerical analysis and field investigation

Preparation of Paste Filling Body and Study on Supported Transportation Laws Using Flac3D Simulation

Deformation Failure and Support Test of Surrounding Rock in Deep Arched Roadway with Straight Wall

Failure analysis and control technology of intersections of large-scale variable cross-section roadways in deep soft rock

Research and Practice on Filling Technology of Fully Mechanized Coal Mining Face through Trend Abandoned Roadway

Analysis of Surrounding Rock Control Technology and Its Application on a Dynamic Pressure Roadway in a Thick Coal Seam

Field and Numerical Study on Deformation and Failure Characteristics of Deep High-Stress Main Roadway in Dongpang Coal Mine