Abstract:The development of Zn-air batteries with a high energy density of 1350 W h kg-1 is one of the breakthroughs required to achieve a low carbon society. However, morphology control of the Zn negative electrode during charge/discharge (Zn-deposition/stripping) is essential for practical application. Considering the manufacturing process, a simple strategy is preferable. Herein, we employed surfactants as an inhibitor of the formation of mossy and dendrite Zn structures, and studied electrochemical Zn growth from the perspective of the electric charge of the surfactant. Even by using an additive free electrolyte of 0.25 M ZnO + 4 M KOH and with 1 mM sodium dodecyl sulfate (SDS: anionic surfactant) or polyacrylic acid (PAA: non-ionic surfactant), mossy and dendrite formations were unavoidable irrespective of the current density. On the other hand, a cationic surfactant, trimethyloctadecylammonium chloride (STAC), suppressed the shape change and resulted in a smooth and dense morphology. Zeta potential measurements, kinetic current densities observed from Tafel plots, and constant potential electrolysis indicate that quaternary ammonium cations (STAC) with bulky size adsorb onto protrusions which are the cause of shape change and suppress Zn deposition in the region to promote lateral growth. Although the adsorption of STAC increased the average overvoltage for Zn-deposition/stripping in a symmetric Zn|Zn cell under a current density of 10 mA cm-2, significantly stable behavior continued for 200 h. In contrast, the overvoltage of the additive free system suddenly increased after 156 h, associated with the accumulation of insulating ZnO and Zn(OH)2 formed on the Zn surface. In charge-discharge tests using an asymmetric Cu|Zn cell, the coulombic efficiency in the additive free electrolyte was less than 95%, whereas the addition of STAC at 1 mM achieved superior cycling performance without any capacity loss originating from the generation of dead Zn (electrical isolation). These results demonstrate that the addition of STAC is a promising method of controlling the Zn morphology.

Morphology Control of Electrodeposited Zinc from Alkaline Zincate Solutions for Rechargeable Zinc Air Batteries

A Homogeneous Plating/stripping Mode with Fine Grains for Highly Reversible Zn Anodes

Electrocrystallization Regulation Enabled Stacked Hexagonal Platelet Growth Toward Highly Reversible Zinc Anodes

Ordered Planar Plating/stripping Enables Deep Cycling Zinc Metal Batteries

Morphology control of zinc electrodeposition by surfactant addition for alkaline-based rechargeable batteries

Dickite Nanolayers for Ultrathin Anode Coatings in Highly Stable Zinc-Ion Batteries

Morphology Control of Zinc Regeneration for Zinc–air Fuel Cell and Battery

Effects of Surface Conditions of Zinc and Additives on Electrodeposition of Zinc from Zincate Solutions

Elucidating the Performance Variations and Critical issues of Zn Electrodes in Different Types of Aqueous Electrolytes for Zn-based Rechargeable Batteries

Influence of Cathodic Overpotential and Zincate Concentration on Zinc Deposition in Alkaline Solution

Manipulation of Zn Deposition Behavior to Achieve High-Rate Aqueous Zinc Batteries via High Valence Zirconium Ions

Understanding and Controlling the Nucleation and Growth of Zn Electrodeposits for Aqueous Zinc-Ion Batteries

Regulating Zn Ion Desolvation and Deposition Chemistry Toward Durable and Fast Rechargeable Zn Metal Batteries

Regulating Zinc Nucleation Sites and Electric Field Distribution to Achieve High-Performance Zinc Metal Anode via Surface Texturing.

A review on zinc electrodes in alkaline electrolyte: Current challenges and optimization strategies

Regulating "Tip Effect" and Zn2+‐Deposition Kinetics by In Situ Constructing Interphase for Low Voltage Hysteresis and Dendrite‐Free Zn Anode

Achieving Stable Zinc Metal Anodes by Regulating Ion Transfer and Desolvation Behavior.

On the Morphology of Zinc Electrodeposition from Alkaline Solutions

Realizing Textured Zinc Metal Anodes through Regulating Electrodeposition Current for Aqueous Zinc Batteries.

Electrodeposited Growth Habit and Growth Mechanism of ZnO As Anode Material of Secondary Alkaline Zn Battery

Regulating electrodeposition morphology in high-capacity aluminium and zinc battery anodes using interfacial metal–substrate bonding