Abstract:The investigation results of friction and wear of the developed detonation composite coatings FeAl2-Ti-Si-B under high-temperature friction conditions are presented. The choice of FeAl2-Ti-Si-B composition and its optimal content for spraying wear-resistant coatings loaded with friction under high-temperature conditions are justified. It is noted that the alloying elements at definite concentrations and technological parameters of spraying have a positive influence on the structure, properties, and quality assurance of multicomponent coatings. It is shown that the introduction of silicon and boron contributes the formation of hard-alloy high-temperature compounds with increased wear resistance. The maximum microhardness corresponds to the Cr-Si coatings with ~ 28 % titan content. In addition, the mechanical properties of the obtained material are improved by additional alloying of ~ 22 % silicon and bor. In turn, the coatings plating at a working gas flow rate in a ratio for acetylene ~ (20/25) l/min and oxygen ~ (22/27) l/min provides the chemical composition and spraying process parameters permanence as well as constant properties of coatings. The obtained results show that for the coatings of FeAl2-Ti-Si-B system at loading 5.0 MPa, sliding speed 1.5 m/s, and temperature up to 650 °C the stable performance of structural adaptability, which ensures the friction and wear parameters minimization, is demonstrated. The metallographic analysis and strip chart recording of specimens indicate that the friction surfaces are characterized by the absence of visible defects; the separate cold-welded regions are located in thin-film surface layers. The composition, structure, and tribological durability of coatings produced from the elements of the country's resource base were studied; their high adhesion, physical and mechanical characteristics and wear resistance under high-temperature conditions were defined. The thin-film surface structure patterns and properties were investigated with the help of modern physical and chemical methods of analysis. It was determined that the combination of mechanical, physical, and chemical properties of the investigated coatings provides vide opportunities for their usage as effective materials under high-temperature wear conditions. According to the test results, the application of the investigated composite coatings for friction unit efficiency improvement provides their operational reliability in accordance with requirements and opportunities that appear with the development of a new competitive material for wear-resistant coatings obtained with the help of the detonation method. Keywords: detonation coating: wear resistance, surface layer, structural adaptability, temperature.

Preparation and characterisation of TIG-alloyed hybrid composite coatings for high-temperature tribological applications

Evaluation on tribological characteristics of (TiC+TiB)/Ti-6Al-4V composite in the range from 25 C to 600 C

Tribological performance and high temperature oxidation behaviour of thermal sprayed Ni- and NiCrAlY-based composite coatings

Wear Behavior of Ti6Al4V Based Hybrid Composites Reinforced with TiB2(7.5%) + TiC (7.5%)

Development of Al-Ni-TiC Composite Coating on Commercially Pure Al Using Tungsten Inert Gas Welding Route and its Wear Behavior

In situ synthesized TiB-TiN reinforced Ti6Al4V alloy composite coatings: microstructure, tribological and in-vitro biocompatibility

Preparation, Mechanical Properties and Cyclic Oxidation Behavior of the Nanostructured NiCrCoAlY-TiB2 Coating

Microstructure, Mechanical Properties and High Temperature Tribological Behavior of NiAl-based Composites

Mechanical, Tribological and Oxidation Resistance Properties of Ni-based Self-Lubricating Composite Coatings at Elevated Temperature by APS

Tribological and Structural Effects of Titanium Carbide and Hexagonal Boron Nitride Reinforcement on Aluminum Matrix Hybrid Composites

Wear Rate of Titanium Matrix Composite Coating at High Temperature Further Increased by Non-Stoichiometric TixC Oxidation

Microstructural and tribological characterization of NiAl matrix self-lubricating composite coatings by atmospheric plasma spraying

State-of-the-Art Developments in Advanced Hard Ceramic Coatings Using PVD Techniques for High-Temperature Tribological Applications

Tribo-Mechanical Properties of HVOF Deposited Fe₃Al Coatings Reinforced with TiB₂ Particles for Wear-Resistant Applications

High temperature tribological behaviors and wear mechanisms of NiAl-MoO3/CuO composite coatings

Microstructure and performance of (CoCrNi) 88 Al 6 Ti 6 -cBN composite coatings by high-speed laser cladding (HSLC): A novel strategy for synergizing wear-resistance and friction reduction

High temperature tribological performance of nickel-based composite coatings by incorporating multiple oxides (TiO2–ZnO–MoO3)

Influence of CePO4 on High Temperature Anti-Friction and Anti-Wear Behaviors of Nickel-Based H-Bn Composite Coatings

High temperature and room temperature tribological behaviors of in-situ carbides reinforced Ni-based composites by reactive sintering Ni and Ti2AlC precursor

Nanocomposite coatings for wear protection at high temperatures

Microstructure and tribological behaviors of laser cladded CuAlMnTi–xTiC composite coatings at elevated temperature