Stabilizing electrodeposition in elastic solid electrolytes containing immobilized anions

Mukul D Tikekar,Lynden A Archer,Donald L Koch,Mukul D. Tikekar,Lynden A. Archer,Donald L. Koch

DOI: https://doi.org/10.1126/sciadv.1600320

IF: 13.6

2016-07-01

Science Advances

Abstract:Elastic deformation in solid electrolytes with immobilized anions suppresses dendritic electrodeposition of metals.

multidisciplinary sciences

What problem does this paper attempt to address?

Confining electrodeposition of metals in structured electrolytes

Snehashis Choudhury,Duylinh Vu,Alexander Warren,Mukul D. Tikekar,Zhengyuan Tu,Lynden A. Archer

DOI: https://doi.org/10.1073/pnas.1803385115

IF: 11.1

2018-06-11

Proceedings of the National Academy of Sciences

Abstract:Significance Electrochemical cells based on lithium and sodium metal anodes are considered among the most versatile platforms for high-energy electrical energy storage. Unfortunately, unstable dendritic metal deposition at currents below the diffusion limit lead to premature cell failure by internal short circuits. In a volatile electrolyte, the ohmic heat generated by these shorts pose significant safety risks. The article reports that electrodeposition of metals can be stabilized by confining ion transport to length scales below a few hundred nanometers. It is also shown that dendrite growth can be arrested in electrolytes with mechanical moduli well below that of the metal. This finding contradicts current orthodoxy, which holds that solid-state electrolytes with moduli higher than the metal are required for preventing dendrite growth.
Role of anisotropy in determining stability of electrodeposition at solid-solid interfaces

Zeeshan Ahmad,Venkatasubramanian Viswanathan

DOI: https://doi.org/10.1103/PhysRevMaterials.1.055403

2017-11-05

Abstract:We investigate the stability of electrodeposition at solid-solid interfaces for materials exhibiting an anisotropic mechanical response. The stability of electrodeposition or resistance to the formation of dendrites is studied within a linear stability analysis. The deformation and stress equations are solved using the Stroh formalism and faithfully recover the boundary conditions at the interface. The stability parameter is used to quantify the stability of different solid-solid interfaces incorporating the full anisotropy of the elastic tensor of the two materials. Results show a high degree of variability in the stability parameter depending on the crystallographic orientation of the solids in contact, and point to opportunities for exploiting this effect in developing Li metal anodes.

Materials Science
Linear stability analysis of transient electrodeposition in charged porous media: suppression of dendritic growth by surface conduction

Edwin Khoo,Hongbo Zhao,Martin Z. Bazant

DOI: https://doi.org/10.48550/arXiv.1901.05033

IF: 2.552

2019-01-15

Chemical Physics

Abstract:We study the linear stability of transient electrodeposition in a charged random porous medium, whose pore surface charges can be of any sign, flanked by a pair of planar metal electrodes. Discretization of the linear stability problem results in a generalized eigenvalue problem for the dispersion relation that is solved numerically, which agrees well with the analytical approximation obtained from a boundary layer analysis valid at high wavenumbers. Under galvanostatic conditions in which an overlimiting current is applied, in the classical case of zero surface charges, the electric field at the cathode diverges at Sand's time due to electrolyte depletion. The same phenomenon happens for positive charges but earlier than Sand's time. However, negative charges allow the system to sustain an overlimiting current via surface conduction past Sand's time, keeping the electric field bounded. Therefore, at Sand's time, negative charges greatly reduce surface instabilities and suppress dendritic growth, while zero and positive charges magnify them. We compare theoretical predictions for overall surface stabilization with published experimental data for copper electrodeposition in cellulose nitrate membranes and demonstrate good agreement between theory and experiment. We also apply the stability analysis to how crystal grain size varies with duty cycle during pulse electroplating.
Stability Criterion for Electrodeposition in Solid-State Batteries with Metallic Anodes

Yuanpeng Liu,Jiawei Zhang,Bowen Zhang,Haowen Gao,Dongjiang Chen,Mingsheng Wang,Changguo Wang

DOI: https://doi.org/10.1103/prxenergy.3.013010

2024-01-01

PRX Energy

Abstract:We establish an analytical criterion for stable electrodeposition by combining electrochemistry and mechanics. In situ experiments combined with molecular simulations are performed to validate the robustness of the theoretical predictions. Our analysis shows that stable electrodeposition is intimately linked with the interfacial defect size, fracture toughness, and molar volume of solid electrolytes. We find an exponential scaling law between the critical current density and the interfacial defect size, and the inherent softening in strength of grain boundaries lowers the critical current density in polycrystalline solid electrolytes. Modeling and analyses provide roadmaps to design solid electrolytes with metallic anodes for achieving stable electrodeposition.
Stability of Electrodeposition at Solid-Solid Interfaces and Implications for Metal Anodes

Zeeshan Ahmad,Venkatasubramanian Viswanathan

DOI: https://doi.org/10.1103/physrevlett.119.056003

IF: 8.6

2017-08-04

Physical Review Letters

Abstract:We generalize the conditions for stable electrodeposition at isotropic solid-solid interfaces using a kinetic model which incorporates the effects of stresses and surface tension at the interface. We develop a stability diagram that shows two regimes of stability: a previously known pressure-driven mechanism and a new density-driven stability mechanism that is governed by the relative density of metal in the two phases. We show that inorganic solids and solid polymers generally do not lead to stable electrodeposition, and provide design guidelines for achieving stable electrodeposition.

physics, multidisciplinary
Dendrite Suppression by Shock Electrodeposition in Charged Porous Media

Ji-Hyung Han,Miao Wang,Peng Bai,Fikile R Brushett,Martin Z Bazant

DOI: https://doi.org/10.1038/srep28054

2016-06-16

Abstract:It is shown that surface conduction can stabilize electrodeposition in random, charged porous media at high rates, above the diffusion-limited current. After linear sweep voltammetry and impedance spectroscopy, copper electrodeposits are visualized by scanning electron microscopy and energy dispersive spectroscopy in two different porous separators (cellulose nitrate, polyethylene), whose surfaces are modified by layer-by-layer deposition of positive or negative charged polyelectrolytes. Above the limiting current, surface conduction inhibits growth in the positive separators and produces irregular dendrites, while it enhances growth and suppresses dendrites behind a deionization shock in the negative separators, also leading to improved cycle life. The discovery of stable uniform growth in the random media differs from the non-uniform growth observed in parallel nanopores and cannot be explained by classic quasi-steady "leaky membrane" models, which always predict instability and dendritic growth. Instead, the experimental results suggest that transient electro-diffusion in random porous media imparts the stability of a deionization shock to the growing metal interface behind it. Shock electrodeposition could be exploited to enhance the cycle life and recharging rate of metal batteries or to accelerate the fabrication of metal matrix composite coatings.
Regulating Zn-ion Solvation Structure and Zn(002) Deposition for Stable Zn Anode

Quan Zong,Yifei Yu,Chaofeng Liu,Qiaoling Kang,Bo Lv,Daiwen Tao,Jingji Zhang,Jiangying Wang,Qilong Zhang,Guozhong Cao

DOI: https://doi.org/10.1016/j.cej.2023.147759

IF: 15.1

2024-01-01

Chemical Engineering Journal

Abstract:Severe side reactions and Zn dendrite growth are two main causes deteriorating the stability of zinc metal anodes. N,N-dimethylpropionamide (DMP) is investigated as an electrolyte additive to suppress side reactions and regulate Zn deposition. Experimental results and theoretical calculations demonstrate that the DMP additive can facilitate solvation structure of hydrated Zn2+ and electrode-electrolyte interface in aqueous ZnSO4 electrolyte. DMP develops strong coordination with Zn2+ through the carbonyl group to reduce the water activity, consequently alleviating the water-associated side reactions. DMP prefers to adsorb on (100) and (101) planes rather than (002), inducing the preferential growth of Zn along the (002) crystal plane. As a result, the ZnSO4 + 10 % DMP electrolyte enables stable Zn plating/stripping in Zn||Zn symmetric cells with a capacity of 1 mAh cm-2 at 1 mA cm-2 for 4000 h, and offers good reversibility in Zn||Cu cells with an average Coulombic efficiency of 99.7 % over 2000 cycles. The coupled Zn||NH4V4O10 full cell using ZnSO4 with 10 % DMP additive exhibits enhanced stability.
Stable Lithium Electrodeposition in Liquid and Nanoporous Solid Electrolytes

Yingying Lu,Zhengyuan Tu,Lynden Archer

DOI: https://doi.org/10.1038/nmat4041

2014-04-25

Abstract:Rechargeable lithium, sodium, and aluminum metal-based batteries are among the most versatile platform for high-energy, cost effective electrochemical energy storage. Non-uniform metal deposition and dendrite formation on the negative electrode during repeated cycles of charge and discharge are major hurdles to commercialization of energy storage devices based on each of these chemistries. A long held view is that unstable electrodeposition is a consequence of inherent characteristics of these metals and their inability to form uniform electrodeposits on surfaces with inevitable defects. We report on electrodeposition of lithium in simple liquid electrolytes and in nanoporous solids infused with liquid electrolytes. We find that simple liquid electrolytes reinforced with halogenated salt blends exhibit stable long-term cycling at room temperature, often with no signs of deposition instabilities over hundreds of cycles of charge and discharge and thousands of operating hours. We rationalize these observations with the help of surface energy data for the electrolyte/lithium interface and impedance analysis of the interface during different stages of cell operation. Our findings provide support for an important recent theoretical prediction that the surface mobility of lithium is significantly enhanced in the presence of lithium halide salts.

Materials Science
Design principles for anode stable solid-state electrolytes

Tan-Lien Pham,Lin Wang,Bin Ouyang

DOI: https://doi.org/10.1039/d4ta02269f

IF: 11.9

2024-07-13

Journal of Materials Chemistry A

Abstract:Metal containing oxides and halides offer a wide range of design spaces for solid-state electrolytes. However, the stability of these electrolytes at the anode/electrolyte interface remains a concern. It is commonly believed that electrolytes containing metals, such as lithium perovskite and lithium metal halides, are inherently unstable at the anode. This issue of electrochemical stability has been somewhat overlooked amidst the surge of research focusing on the development of new superionic conductors. In this work, we employ a computational framework to uncover the underlying causes of anode instability in different electrolytes that contain metals. Our findings indicate that deficient compounds in lithium, such as lithium perovskite or lithium metal halide, tend to be unstable at the anode regardless of the metal chemistry involved. This instability is primarily due to their unsuitable lithium stoichiometry, positioning them in regions of the phase diagram where stronger decomposition phases prevail. Conversely, lithium-rich compounds, such as newly identified overlithiated disordered rocksalt-type electrolytes, exhibit significantly better anode stability. Additionally, our research also shows that while anode stability is generally less problematic for sodium metal oxide-based electrolytes in solid-state sodium-ion batteries, it remains a challenge for sodium metal halides. This work rationales the choice of metal species and structural phases as stoichiometry for more electrochemical stable solid-state electrolytes.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Regulating Na‐ion Solvation in Quasi‐Solid Electrolyte to Stabilize Na Metal Anode

Xiaoyan Zhou,Zhuo Li,Wanming Li,Xiaogang Li,Jialong Fu,Lu Wei,Hui Yang,Xin Guo

DOI: https://doi.org/10.1002/adfm.202212866

IF: 19

2022-12-29

Advanced Functional Materials

Abstract:Random diffusion of Na+ in liquid electrolytes leads to dendritic deposition (top), however, the Na+ migration in quasi‐solid electrolytes is guided by carbonyl groups (OC), which results in the uniform Na deposition and inhibits the dendrite formation (bottom). Sodium metal batteries are promising for cost‐effective energy storage, however, the sluggish ion transport in electrolytes and detrimental sodium‐dendrite growth stall their practical applications. Herein, a cross‐linking quasi‐solid electrolyte with a high ionic conductivity of 1.4 mS cm−1 at 25 °C is developed by in‐situ polymerizing poly (ethylene glycol) diacrylate‐based monomer. Benefiting from the refined solvation structure of Na+ with a much lower desolvation barrier, random Na+ diffusion on the Na surface is restrained, so that the Na dendrite formation is suppressed. Consequently, symmetrical Na||Na cells employing the electrolyte can be cycled >2000 h at 0.1 mA cm−2. Na3V2(PO4)3||Na batteries reveal a high discharge specific capacity of 66.1 mAh g−1 at 15 C and demonstrate stable cycling over 1000 cycles with a capacity retention of 83% at a fast rate of 5 C.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Suppression of electroconvection due to van der Waals attraction of polymer additives towards the metal electrode

Ankush Mukherjee,Lynden A. Archer,Donald L. Koch

DOI: https://doi.org/10.48550/arXiv.2210.15758

IF: 0.673

2022-10-27

Fluid Dynamics

Abstract:Electroconvection in rechargeable batteries enhances the growth of dendrites at the electrode surface. The addition of low molecular weight polymers to the electrolyte in batteries results in the formation of a thin layer of higher polymer concentration near the electrode. This is due to van der Waals forces of attraction between the metal electrode and the polymers dissolved in the electrolyte. The van der Waals forces act as a restoring body force on the electrolyte and oppose the growth of perturbations. Using linear stability analysis, we show that this force opposes electroconvective flow. This increases the critical voltage required for the onset of electroconvection.
Morphological instability during steady electrodeposition at overlimiting currents

Christoffer P. Nielsen,Henrik Bruus

DOI: https://doi.org/10.1103/PhysRevE.92.052310

2015-05-28

Abstract:We present a linear stability analysis of a planar metal electrode during steady electrodeposition. We extend the previous work of Sundstrom and Bark by accounting for the extended space-charge density, which develops at the cathode once the applied voltage exceeds a few thermal voltages. In accordance with Chazalviel's conjecture, the extended space-charge region is found to greatly affect the morphological stability of the electrode. To supplement the numerical solution of the stability problem, we have derived analytical expressions valid in limit of low and high voltage, respectively.

Fluid Dynamics
Stabilizing Lithium Metal Electrodes Through Specific Adsorption and Regulated Solvation Structure

Chang Zhou,Yuhao Zhou,Shuai Hao,Guoran Li,Sheng Liu,Xueping Gao

DOI: https://doi.org/10.1016/j.xcrp.2024.101999

IF: 8.9

2024-01-01

Cell Reports Physical Science

Abstract:Lithium (Li)-metal batteries hold great promise for high-energy-density energy-storage systems. However, the instability of Li electrodes, particularly due to sluggish electrode kinetics and parasitic reactions, remains a significant challenge. Here, we propose a synergistic strategy for constructing stable Li electrodes with favorable electrode kinetics that enable dendrite-free and gas-suppressed Li-metal batteries by regulating the Li-ion distribution in the electric double layer and Li+ solvation structure. We demonstrate that the specific adsorption of non-sacrificial surfactant ammonium perfluoro(2-methyl-3-oxahexanoate) can be reinforced by LiNO3, which also facilitates the desolvation process via synergistic coordination of Li+ solvation structures, further accelerating Li-electrode interfacial reaction kinetics. Under this synergistic effect, the Li–Li symmetric cells can stably operate over 10,000 h, and the Li–Li4Ti5O12 full cells achieve ultrahigh capacity retention (98%) over 1,000 cycles. This work provides a practical strategy for stabilizing Li anodes of high-energy-density secondary Li-metal batteries.
Machine Learning Enabled Computational Screening of Inorganic Solid Electrolytes for Dendrite Suppression with Li Metal Anode

Zeeshan Ahmad,Tian Xie,Chinmay Maheshwari,Jeffrey C. Grossman,Venkatasubramanian Viswanathan

DOI: https://doi.org/10.1021/acscentsci.8b00229

2018-04-13

Abstract:Next generation batteries based on lithium (Li) metal anodes have been plagued by the dendritic electrodeposition of Li metal on the anode during cycling, resulting in short circuit and capacity loss. Suppression of dendritic growth through the use of solid electrolytes has emerged as one of the most promising strategies for enabling the use of Li metal anodes. We perform a computational screening of over 12,000 inorganic solids based on their ability to suppress dendrite initiation in contact with Li metal anode. Properties for mechanically isotropic and anisotropic interfaces that can be used in stability criteria for determining the propensity of dendrite initiation are usually obtained from computationally expensive first-principles methods. In order to obtain a large dataset for screening, we use machine learning models to predict the mechanical properties of several new solid electrolytes. We train a convolutional neural network on the shear and bulk moduli purely on structural features of the material. We use AdaBoost, Lasso and Bayesian ridge regression to train the elastic constants, where the choice of the model depended on the size of the training data and the noise that it can handle. Our models give us direct interpretability by revealing the dominant structural features affecting the elastic constants. The stiffness is found to increase with a decrease in volume per atom, increase in minimum anion-anion separation, and increase in sublattice (all but Li) packing fraction. Cross-validation/test performance suggests our models generalize well. We predict over 20 mechanically anisotropic interfaces between Li metal and 6 solid electrolytes which can be used to suppress dendrite growth. Our screened candidates are generally soft and highly anisotropic, and present opportunities for simultaneously obtaining dendrite suppression and high ionic conductivity in solid electrolytes.

Materials Science,Machine Learning,Chemical Physics
Controlling Electrostatics to Enhance Conductivity in Structured Electrolytes

Jonathan K. Whitmer,Logan Hennes,Chloe Behringer,Mohsen Farshad,Jennifer L. Schaefer

DOI: https://doi.org/10.26434/chemrxiv-2024-frkvj

2024-10-07

Abstract:Solid-state electrolytes are currently being explored as a safe material capable of addressing consumer energy-storage demands. Solid polymer electrolytes, in particular, offer a high energy density and improved safety when compared to liquid-based electrolytes, but tend to have a significantly lower ionic conductivity. We hypothesize structured ionic liquids can enhance conductivity. Here, we explore the performance of these materials through coarse-grained molecular dynamics simulation. While we observe similar phase behavior (incorporating solid, smectic, and liquid phases) to that seen in experiments, we also observe significantly more mobility in the cationic species compared to the anionic species before the system reaches an arrest transition. We further discuss how the general results within this paper can guide further studies and target the design of new highly conductive solid electrolytes with the potential to enable the use of multivalent ionic species as ion conductors.

Chemistry
Solid-state polymer electrolytes for high-performance lithium metal batteries

Snehashis Choudhury,Sanjuna Stalin,Duylinh Vu,Alexander Warren,Yue Deng,Prayag Biswal,Lynden A. Archer

DOI: https://doi.org/10.1038/s41467-019-12423-y

IF: 16.6

2019-09-27

Nature Communications

Abstract:Abstract Electrochemical cells based on alkali metal anodes are receiving intensive scientific interest as potentially transformative technology platforms for electrical energy storage. Chemical, morphological, mechanical and hydrodynamic instabilities at the metal anode produce uneven metal electrodeposition and poor anode reversibility, which, are among the many known challenges that limit progress. Here, we report that solid-state electrolytes based on crosslinked polymer networks can address all of these challenges in cells based on lithium metal anodes. By means of transport and electrochemical analyses, we show that manipulating thermodynamic interactions between polymer segments covalently anchored in the network and “free” segments belonging to an oligomeric electrolyte hosted in the network pores, one can facilely create hybrid electrolytes that simultaneously exhibit liquid-like barriers to ion transport and solid-like resistance to morphological and hydrodynamic instability.

multidisciplinary sciences
Stable Lithium Deposition Using a Self-Optimizing Solid Electrolyte Composite

Justin M. Whiteley,Simon Hafner,Chengpu Zhu,Wei Zhang,Se-Hee Lee

DOI: https://doi.org/10.1149/2.0331713jes

IF: 3.9

2017-01-01

Journal of The Electrochemical Society

Abstract:We report the ability of solid electrolyte in polymer membrane (SEPM) system to suppress lithium dendrites. The concept of impregnation of material in the pore space of a solid electrolyte is not an entirely new concept, although none of these studies effectively demonstrated blocking of lithium dendrite growth in a solid state configuration. In this study, we explored a new mechanism of lithium dendrite suppression by introducing a self-healing polymer with solid electrolyte to form a composite. The mechanism is correlated to self-healing ability through the use of temperature and current density. Galvanostatic and cycling tests reveal a system which demonstrates a 50X improvement in performance over a pure solid electrolyte separator. We conclude that this is not an effect of the introduction of any polymer into the solid electrolyte system, but is specific to the imine-based self-healing polymer. We postulate that the polymer acts to optimize an interface between lithium and the solid electrolyte as well as form an optimized matrix between solid electrolyte particles. With further optimization, this new system can be a viable option to produce thin solid membranes in a lithium metal configuration. (C) 2017 The Electrochemical Society. All rights reserved.
Deflecting Dendrites by Introducing Compressive Stress in Li7La3Zr2O12 Using Ion Implantation

Florian Flatscher,Juraj Todt,Manfred Burghammer,Hanne-Sofie Søreide,Lukas Porz,Yanjun Li,Sigurd Wenner,Viktor Bobal,Steffen Ganschow,Bernhard Sartory,Roland Brunner,Constantinos Hatzoglou,Jozef Keckes,Daniel Rettenwander

DOI: https://doi.org/10.1002/smll.202307515

IF: 13.3

Small

Abstract:Lithium dendrites belong to the key challenges of solid-state battery research. They are unavoidable due to the imperfect nature of surfaces containing defects of a critical size that can be filled by lithium until fracturing the solid electrolyte. The penetration of Li metal occurs along the propagating crack until a short circuit takes place. It is hypothesized that ion implantation can be used to introduce stress states into Li6.4La3Zr1.4Ta0.6O12 which enables an effective deflection and arrest of dendrites. The compositional and microstructural changes associated with the implantation of Ag-ions are studied via atom probe tomography, electron microscopy, and nano X-ray diffraction indicating that Ag-ions can be implanted up to 1 µm deep and amorphization takes place down to 650-700 nm, in good agreement with kinetic Monte Carlo simulations. Based on diffraction results pronounced stress states up to -700 MPa are generated in the near-surface region. Such a stress zone and the associated microstructural alterations exhibit the ability to not only deflect mechanically introduced cracks but also dendrites, as demonstrated by nano-indentation and galvanostatic cycling experiments with subsequent electron microscopy observations. These results demonstrate ion implantation as a viable technique to design "dendrite-free" solid-state electrolytes for high-power and energy-dense solid-state batteries.
Screening of Electrolyte-Anode Buffers to Suppress Lithium Dendrite Growth in All-Solid-State Batteries

Weiyu Li,Hamdi A. Tchelepi,Daniel M. Tartakovsky,Hamdi A Tchelepi

DOI: https://doi.org/10.1149/1945-7111/acd0da

IF: 3.9

2023-04-29

Journal of The Electrochemical Society

Abstract:Dendritic growth of lithium (Li) metal is a leading cause of degradation and catastrophic failure of all-solid-state batteries (ASSBs) with Li anode. Insertion of a buffer layer between the Li metal and the solid electrolyte is known to ameliorate this phenomenon, yet the identification of an optimal buffer material, and the design of ASSBs that can be manufactured at scale, remains elusive and largely driven by trial-and-error experimentation. Our analysis seeks to accelerate the buffer-materials discovery by elucidating the conditions under which the buffer's presence stabilizes electrodeposition on the Li anode in ASSBs. The analysis quantifies the interfacial instability associated with dendrite formation in terms of the battery's operating conditions and the electrochemical and physical properties of the buffer material and solid electrolyte. The model predicts that, among several prospective buffer materials, Ag, Al, Sn, and antiperovskite super ionic conductor, Li 3 S(BF 4 ) 0.5 Cl 0.5 , are effective in stabilizing electrodeposition and suppressing dendrite growth. Our model's predictions of the dendrite suppression abilities of different buffer materials are consistent with the published experimental findings. The model can be used to guide experimental and computational discovery of new buffer materials that match a particular electrolyte.

electrochemistry,materials science, coatings & films
Stabilization of lithium metal in concentrated electrolytes: effects of electrode potential and solid electrolyte interphase formation

Anusha Pradhan,Shoma Nishimura,Yasuyuki Kondo,Tomoaki Kaneko,Yu Katayama,Keitaro Sodeyama,Yuki Yamada

DOI: https://doi.org/10.1039/d4fd00038b

2024-04-18

Faraday Discussions

Abstract:Lithium (Li) metal negative electrodes have enticed a wide attention for high-energy-density batteries. However, its low Coulombic efficiency (CE) due to parasitic electrolyte reduction has been an alarming concern. Concentrated electrolytes are one of the promising concepts that can stabilize the Li metal/electrolyte interface, thus increasing the CE; however, its mechanism has been still controversial. In this work, we used LiN(SO 2 F) 2 (LiFSI) and weakly solvating 1,2-diethoxyethane (DEE) as a model electrolyte to study how its liquid structure changes upon increasing salt concentration and how it is linked to the Li plating/stripping CE. Based on previous works, we focused on Li electrode potential ( E Li with reference to the redox of ferrocene) and solid electrolyte interphase (SEI) formation. Although the E Li shows a different trend in DEE as compared to conventional 1,2-dimethoxyethane (DME), which is accounted for by different ion-pairing states of Li + and FSI - , the E Li -CE plots are overlapped for both electrolytes, suggesting that the E Li is one of the dominant factors of the CE. On the other hand, the extensive ion pairing results in the upward shift of FSI - reduction potential, as demonstrated both experimentally and theoretically, which promotes FSI - -derived inorganic SEI. Both E Li and SEI contribute to increasing the Li plating/stripping CE.

chemistry, physical

Stabilizing electrodeposition in elastic solid electrolytes containing immobilized anions

Confining electrodeposition of metals in structured electrolytes

Role of anisotropy in determining stability of electrodeposition at solid-solid interfaces

Linear stability analysis of transient electrodeposition in charged porous media: suppression of dendritic growth by surface conduction

Stability Criterion for Electrodeposition in Solid-State Batteries with Metallic Anodes

Stability of Electrodeposition at Solid-Solid Interfaces and Implications for Metal Anodes

Dendrite Suppression by Shock Electrodeposition in Charged Porous Media

Regulating Zn-ion Solvation Structure and Zn(002) Deposition for Stable Zn Anode

Stable Lithium Electrodeposition in Liquid and Nanoporous Solid Electrolytes

Design principles for anode stable solid-state electrolytes

Regulating Na‐ion Solvation in Quasi‐Solid Electrolyte to Stabilize Na Metal Anode

Suppression of electroconvection due to van der Waals attraction of polymer additives towards the metal electrode

Morphological instability during steady electrodeposition at overlimiting currents

Stabilizing Lithium Metal Electrodes Through Specific Adsorption and Regulated Solvation Structure

Machine Learning Enabled Computational Screening of Inorganic Solid Electrolytes for Dendrite Suppression with Li Metal Anode

Controlling Electrostatics to Enhance Conductivity in Structured Electrolytes

Solid-state polymer electrolytes for high-performance lithium metal batteries

Stable Lithium Deposition Using a Self-Optimizing Solid Electrolyte Composite

Deflecting Dendrites by Introducing Compressive Stress in Li7La3Zr2O12 Using Ion Implantation

Screening of Electrolyte-Anode Buffers to Suppress Lithium Dendrite Growth in All-Solid-State Batteries

Stabilization of lithium metal in concentrated electrolytes: effects of electrode potential and solid electrolyte interphase formation