Abstract:Summary form only given. Capillary discharge plasmas have been widely used as electrothermal chemical (ETC) launch devices, fusion reactor pellet injectors and high heat flux sources for material studies. In the electro thermal chemical launcher, the mechanisms of the plasma-propellant interaction are critical, with many factors being of potential importance. In particular, the role of plasma radiation is disputed. We will report the effect of three different metal ions and radiation in the capillary discharge plasma on the plasma-propellant interactions. Conventionally, a capillary initiated by a metal wire of about 2 mg and with an ablative liner material (e.g. polyethylene) is used as the plasma generator. The plasma is mainly composed of CO, H + , C, etc. The proportion of metal ions was negligible. We have designed a new capillary discharge plasma generator with different metal powders of higher weight as the initiators. The performance of the new generator is compared with the traditional one through an open-air test. A spectrometer and ICCD were used to measure the surface temperature of the propellants while a CCD was used to visualize the plasma jet. The combustion tests were conducted in a transparent closed vessel, making it possible to measure the plasma parameters at the propellant surface and observe the combustion process in the closed vessel. A fused silica window was placed between the plasma and propellants to ensure that the propellant could only be affected by plasma radiation. The burning rate and the p-t curve were obtained in the tests and the combustion products were analyzed by a mass spectrometer. Interrupted burning tests were also carried out to acquire information about the surface of the propellants at different burning stages. In order to perform accurate modeling of the plasma-propellant interaction, we have also developed a two-dimensional time-dependent capillary discharge model based on a modified ablation model. In our model, special attention is paid to the radial distribution of the capillary discharge plasma characteristics. To investigate the factors that influence the radial distribution, the radial transport of the ablation products is taken into consideration. Further, the competition between the ablation and deposition process with time in the capillary discharge is also studied. The aim of our study are to provide results that will assist the design of new propellants and new plasma generators for the ETC launcher.

Characteristics of a non-volatile liquid propellant in liquid-fed ablative pulsed plasma thrusters

Impulse and Performance Measurements of Electric Solid Propellant in a Laboratory Electrothermal Ablation-Fed Pulsed Plasma Thruster

Electric Solid Propellant Ablation in an Arc Discharge

Application And Development Of The Pulsed Plasma Thruster

Comparative study of plume characteristics of polymeric propellants filled with different oxides for laser-electric hybrid thruster

Liquid-Fed Pulsed Plasma Thruster for Propelling Nanosatellites

Influence of Different Energy Supply Methods on Performance of Ablative Pulsed Plasma Thrusters

Operation Analysis of Pulsed Plasma Thruster

Optimization of Plasma Plume Characteristics Based on Multi-anode Coaxial Ablative Pulsed Plasma Thruster

Experimental investigation on the evolution of plasma properties in the discharge channel of a pulsed plasma thruster

Discharge Characteristics and System Performance of the Ablative Pulsed Plasma Thruster with Different Structural Parameters

Experimental Study of a Low-Voltage Pulsed Plasma Thruster for Nanosatellites

System Analysis and Test-Bed for an Atmosphere-Breathing Electric Propulsion System using an Inductive Plasma Thruster

Design and Performance of an Electrowetting Ionic Liquid Electrospray Thruster Prototype

Fuel Ignition in HTP Hybrid Rockets at Very Low Mass Fluxes: Challenges and Pulsed Preheating Techniques Using Palladium-Coated Catalysts

Comparison of ablators for the polar direct drive exploding pusher platform

Ignition Stability of Electrothermal Pulsed Plasma Thruster

A study of an air-breathing electrodeless plasma thruster discharge

Roles of Metal Ions and Plasma Radiation in the Interactions Between A Capillary Discharge Plasma and Propellants

Cathode-less RF plasma thruster design and optimisation for an atmosphere-breathing electric propulsion (ABEP) system

Reviews of the Propulsive Characteristics Study on Liquid Propellants for Laser Propulsion