Abstract:Fatigue crack growth rate behavior in the threshold and near-threshold regimes for a Ti-6Al-4V solution-treated and over-aged (STOA) alloy was investigated using two test procedures: i ) accelerated load reduction (ALR) utilizing faster load-shed rates than recommended in the ASTM standard E647 load-reduction (LR) test procedure, and ii ) compression pre-cracking constant-amplitude (CPCA) or load-increasing (CPLI) and load-reduction (CPLR). Fatigue crack growth tests were conducted on compact, C(T), specimens (B = 6.35 mm) with two different widths ( W = 51 and 76 mm) at two stress ratios ( R = 0.1 and 0.7). The crack-growth-rate test data were compared to previous test data produced from the same batch of material using the ASTM LR and CPCA test procedures that were tested on C(T) specimens ( W = 25, 51 and 76 mm) over a wide range in stress ratios (R = 0.1, 0.4, and 0.7). Although none of the load-reduction test procedures provided a good representation of the threshold value (Δ K th ) at low R , the CPCA test procedure was the most promising. The LR, ALR, and CPLR test procedures were influenced by prior loading history, leading to higher Δ K th values and slower crack growth rates in the threshold regime due to a rise in the crack-opening loads. The LR and ALR tests at R = 0.1 and shed rates of −0.08, −0.32, and −0.95 mm −1 yielded Δ K th values that were 15 to 38 % higher than the estimated threshold stress-intensity factor range (Δ K * th ) R =0.1 based on the crack-closure model (FASTRAN). The compression pre–cracking test procedures are more accurate alternatives for developing threshold and near-threshold fatigue crack growth rates. Specifically, the CPLR test procedure produced a Δ K th value that was 8–18 % higher than (Δ K * th ) R =0.1 . Additionally, LR and ALR tests produced different Δ K th values as a function of the specimen width for a given load ratio, which violates classical fracture mechanics principles. In addition, the spread in the Δ K -rate data in the low-rate regime was larger than the spread in the mid-rate regime as a function of R , a term referred to as " fanning ". In contrast, the CPCA test procedure produced consistent crack growth rates over the same range of Δ K values examined, independent of the specimen width and these data did not exhibit " fanning " with R . Further research is necessary to develop standard test procedures capable of providing a more definitive representation of the Δ K th value in the threshold regime. However, FASTRAN can serve as a crucial tool in aligning the actual Δ K th values with those obtained through CP testing, thereby bridging the gap and enhancing the reliability of the results.

Construction of Kitagawa–Takahashi diagrams as a function of applied stress ratio

Instrumented indentation measurements of residual stresses around a crack tip under single tensile overloads

Multiaxial Kitagawa analysis of A356-T6

Near-threshold fatigue crack propagation without oxide-induced crack closure

Effect of load ratio and maximum stress intensity on the fatigue threshold in Ti–6Al–4V

A threshold criterion of stress intensity range in a steel sheet

In-situ computed tomography and transient dynamic analysis – failure analysis of a single-lap tensile-shear test with clinch points

Assessing fatigue crack growth thresholds for a Ti-6Al-4V (STOA) alloy using two experimental methods

Distinct Advantages of Circumferential Notch Tensile (CNT) Testing in the Determination of a Threshold for Stress Corrosion Cracking (KISCC)

Simple Scaling as a Tool to Help Assess the Closure-Free da/dN Versus ΔKeff Curve in a Range of Materials

Effect of Load Ratio on Fatigue Crack Growth Behavior of SS316LN using Two-Parameter (ΔK and Kmax) Model

Effect of Specimen Thickness and Stress Intensity Factor Range on Plasticity-Induced Fatigue Crack Closure in A7075-T6 Alloy

Fatigue Crack Growth for Ferritic Steel under Negative Stress Ratio

Cyclic R‐curve measurements for structural metallic alloys

A New Approach to Evaluate Fracture Toughness of Structural Materials

On the validity of the Tada stress intensity factor solution for the single edge notch tension specimen with pinned ends

Unusual Fatigue Crack Growth Behavior of Long Cracks at Low Stress Intensity Factor Ranges

Comparison of Various Intrinsic Defect Criteria to Plot Kitagawa-Takahashi Diagrams in Additively Manufactured AlSi10Mg

Quantification of the Complex Crack Geometry Effect on Fracture Resistance Using Strain-Based Finite Element Damage Analysis

On the Link between Plastic Wake Induced Crack Closure and the Fatigue Threshold

Experimental analysis of the multiaxial failure stress locus of commercially pure titanium at low and high rates of strain