Abstract:Widespread interest has emerged in addressing the energy crisis that makes use of abundant solar energy to simultaneously evaporate water and produce electricity. Photothermal conversion materials (PCMs) and device structures are the two key platforms of photothermal conversion in the process of water evaporation (WE) and thermoelectric (TE) generation, and thus it is very important to reasonably design the structure of PCMs and the corresponding devices. Herein, three-dimensional (3D) and two-dimensional (2D) flexible carbon melamine foam (CMF) combined with Cu particles with excellent plasma effect and CuS with excellent UV-vis light absorption performance were assembled as a PCM (CMF/Cu@CuS). This functionalized porous CMF/Cu@CuS foam can not only realize WE but also simultaneously generate TE via the Seebeck effect. We found that the 3D structure favors WE and the 2D structure favors TE generation. Additionally, the TE generation is significantly impacted by the position of the TE module. Specifically, when the TE module is placed at the bottom of the PCM, the photothermal conversion efficiency (PCE) of the 3D structure reaches 86.8%, while that of the 2D structure is only 68.3% under 1.0 kW m(-2) light irradiation. However, the maximum output TE power of the 2D structure reaches 69.3 mu W cm(-2), which is significantly higher than that by the 3D structure (2.4 mu W cm(-2)). This difference in performance is due to the different thermal management abilities of the devices. The 3D structure can absorb extra heat from the surrounding environment, which is conducive to WE. However, the 3D structure leads to a small temperature difference between the hot and cold sides of the TE module, which is not conducive to TE generation. The 2D structure cannot absorb extra heat from the environment, which is not conducive to WE, but it causes a higher temperature difference between the hot and cold sides of the TE module, and is thus conducive to TE generation. A high WE rate can be attained as well as high TE power produced when the TE module is positioned close to the top surface of the PCM. According to this study, a properly adjusted TE module position is necessary to simultaneously achieve a high WE rate and output TE power.

Multi-scale CuS-rGO pyramidal photothermal structure for Highly Efficient Solar-Driven Water Evaporation and Thermoelectric Power Generation

Lanthanide Doped Two Dimensional Heterostructure Nanosheets with Highly Efficient Harvest Towards Solar Energy

Achieving Solar‐Thermal‐Electro Integration Evaporator Nine‐Grid Array with Asymmetric Strategy for Simultaneous Harvesting Clean Water and Electricity

2D/2D Cs0.32WO3/CuS Nano‐Heterojunctions for Simultaneous High‐Efficiency Solar Desalination, Photocatalytic Decontamination, and Electricity Generation

All-weather Photothermal-Electrothermal Integrated System for Efficient Solar Steam Generation

Efficient Water Transport and Solar Steam Generation Via Radially, Hierarchically Structured Aerogels

Hybrid nanoarchitectonics of carbon/titanium carbide integrated hydrogel/melamine foam for highly efficient solar steam and thermoelectric power generation

Fabrication of high-performance graphene oxide/CuO/Cu 2 O film-coated copper foam for interfacial solar-driven water evaporation

Fabrication of high-performance graphene oxide/CuO/Cu2O film-coated copper foam for interfacial solar-driven water evaporation

Self-regulating and asymmetric evaporator for efficient solar water-electricity generation

Excellent dual-photothermal freshwater collector with high performance in large-scale evaporation

"One stone two birds" or "you can't have your cake and eat it too"? Effects of device dimensions and position of the thermoelectric module on simultaneous solar-driven water evaporation and thermoelectric generation

Intercalation of V2O5 and Polypyrrole into a Graphene Oxide Layer: A Hybrid Multifunctional Photothermal Structure for Efficient Solar Evaporation, Water Purification, Disinfection, and Power Production

Same materials, bigger output: A reversibly transformable 2D–3D photothermal evaporator for highly efficient solar steam generation

Photothermal water evaporation and purification on the interface evaporator constructed by Cu@Bi 2 WO 6 -C

Solar-driven water evaporation using a collaborative photothermal conversion material system based on carbonized waste polyphenylene sulfide and copper sulfide

Structure development of carbon-based solar-driven water evaporation systems

Synergistic Effect Between 0D CQDs and 2D MXene to Enhance the Photothermal Conversion of Hydrogel Evaporators for Efficient Solar Water Evaporation, Photothermal Sensing and Electricity Generation

Highly Efficient Solar Steam Generation and Desalination through Gourd‐flesh Templated Polypyrrole Composite

Catkins based flexible photothermal materials for solar driven interface evaporation collaborative power generation

MXene-reduced graphene oxide sponge-based solar evaporators with integrated water-thermal management by anisotropic design