Abstract:Pulsed thermography is a commonly used non-destructive testing method and is increasingly studied for the assessment of advanced materials such as carbon fibre-reinforced polymer (CFRP). Different processing approaches are proposed to detect and characterize anomalies that may be generated in structures during the manufacturing cycle or service period. In this study, matrix decomposition using Robust PCA via Inexact-ALM is investigated as a pre- and post-processing approach in combination with state-of-the-art approaches (i.e., PCT, PPT and PLST) on pulsed thermography thermal data. An academic sample with several artificial defects of different types, i.e., flat-bottom-holes (FBH), pull-outs (PO) and Teflon inserts (TEF), was employed to assess and compare defect detection and segmentation capabilities of different processing approaches. For this purpose, the contrast-to-noise ratio (CNR) and similarity coefficient were used as quantitative metrics. The results show a clear improvement in CNR when Robust PCA is applied as a pre-processing technique, CNR values for FBH, PO and TEF improve up to 164%, 237% and 80%, respectively, when compared to principal component thermography (PCT), whilst the CNR improvement with respect to pulsed phase thermography (PPT) was 77%, 101% and 289%, respectively. In the case of partial least squares thermography, Robust PCA results improved not only only when used as a pre-processing technique but also when used as a post-processing technique; however, this improvement is higher for FBHs and POs after pre-processing. Pre-processing increases CNR scores for FBHs and POs with a ratio from 0.43% to 115.88% and from 13.48% to 216.63%, respectively. Similarly, post-processing enhances the FBHs and POs results with a ratio between 9.62% and 296.9% and 16.98% to 92.6%, respectively. A low-rank matrix computed from Robust PCA as a pre-processing technique on raw data before using PCT and PPT can enhance the results of 67% of the defects. Using low-rank matrix decomposition from Robust PCA as a pre- and post-processing technique outperforms PLST results of 69% and 67% of the defects. These results clearly indicate that pre-processing pulsed thermography data by Robust PCA can elevate the defect detectability of advanced processing techniques, such as PCT, PPT and PLST, while post-processing using the same methods, in some cases, can deteriorate the results.

Enhancing defect detection in active infrared thermography using adaptive background suppression techniques

Exploratory Factor Analysis for Defect Identification with Active Thermography

Nondestructive detection and analysis based on data enhanced thermography

One-dimensional deep convolutional autoencoder active infrared thermography: Enhanced visualization of internal defects in FRP composites

Deep Autoencoder for Non-destructive Testing of Defects in Polymer Composites

Data Enhancement via Low-Rank Matrix Reconstruction in Pulsed Thermography for Carbon-Fibre-Reinforced Polymers

Thermographic Data Analysis for Defect Detection by Imposing Spatial Connectivity and Sparsity Constraints in Principal Component Thermography

Generative Deep Learning-Based Thermographic Inspection of Artwork

Visual Defect Recognition and Location for Pulsed Thermography Images Based on Defect-background Contrast Analysis

Deep Autoencoder Thermography for Defect Detection of Carbon Fiber Composites

Enhancement of Defect Detectability in Pneumatic Pressure Equipment Using an Automatic Detection Technique in ECPT

Multiview Learning for Subsurface Defect Detection in Composite Products: A Challenge on Thermographic Data Analysis

Robust Principal Component Thermography for Defect Detection in Composites

Improving Visibility of Rear Surface Cracks During Inductive Thermography of Metal Plates Using Autoencoder

Enhanced Diffusion-Based Analysis for Fast Defect Detection in ECPT Image

Spatio-Temporal 3-D Residual Networks for Simultaneous Detection and Depth Estimation of CFRP Subsurface Defects in Lock-In Thermography

Enhanced Infrared Sparse Pattern Extraction and Usage for Impact Evaluation of Basalt-Carbon Hybrid Composites by Pulsed Thermography

An Automated Pipeline for Dynamic Detection of Sub-Surface Metal Loss Defects across Cold Thermography Images

Improvement of Defect Feature Extraction in Eddy Current Pulsed Thermography.

A Reliability Study on Automated Defect Assessment in Optical Pulsed Thermography