Abstract:Magnesium sheet metal alloys have a hexagonal close packed (hcp) crystal structure that leads to severe evolving anisotropy and tension-compression asymmetry as a result of the activation of different deformation mechanisms (slip and twinning) that are extremely challenging to model numerically. The low density of magnesium alloys and their high specific strength relative to steel and aluminum alloys make them promising candidates for automotive light-weighting but standard phenomenological plasticity models cannot adequately capture the complex plastic response of these materials. In this study, the constitutive plastic behavior of a rare-earth magnesium alloy sheet, ZEK100 (O-temper), was considered at room temperature, under quasi-static conditions. The CPB06 yield criterion for hcp materials was employed along with a non-associative flow rule in which the yield function and plastic potential were calibrated for a range of plastic deformation levels to account for evolving anisotropy under proportional loading. The non-associative flow rule has not previously been applied to magnesium alloys which require the use of flexible constitutive models to capture the severe anisotropy and its evolution with plastic deformation. The non-associative flow rule can provide the required flexibility by decoupling the yield function and plastic potential. For the associative flow rule, such flexibility can only be achieved by multiple linear transformations of the stress tensor resulting in expensive models for calibration and simulations. The constitutive model was implemented as a user material subroutine (UMAT) within the commercial finite element software, LS-DYNA, for general 3-D stress states along with an interpolation technique to consider the evolution of anisotropy based upon the plastic work. To evaluate the accuracy of the implemented model, predictions of a single-element model were compared with the experimental results in terms of flow stresses and plastic flow directions under various proportional loading conditions and along different test directions. Finally, to assess the predictive capabilities of the model, full-scale simulations of coupon-level formability experiments were performed and compared with experimental results in terms of far-field load-displacement and local strain paths. Using these experiments, the constitutive model was evaluated across the full range of representative stress states for sheet metal forming operations. It was shown that the predictions of the model were in very good agreement with experimental data.

A Review of the Anomalous Dynamic Behavior in Magnesium Alloys

Dynamic plasticity of AZ31 magnesium alloy: Experimental investigation and constitutive modeling

New Studies in the Field of Alloying and Deformation of Modern Magnesium Alloys. Review

Anomalous Hardening in Magnesium Driven by a Size-Dependent Transition in Deformation Modes

Excellent room temperature deformability in high strain rate regimes of magnesium alloy

Designing highly ductile magnesium alloys: current status and future challenges

Hot Deformation Characteristics and Dynamic Recrystallization Mechanisms of a Semi-Solid Forged AZ91D Magnesium Alloy

Cyclic deformation behavior of rare-earth containing magnesium alloys

Application of an Evolving Non-Associative Anisotropic-Asymmetric Plasticity Model for a Rare-Earth Magnesium Alloy

MAGNESIUM ALLOYS: PROSPECTIVE INDUSTRIES OF APPLICATION, ADVANTAGES AND DISADVANTAGES (review). Part 2. Mechanism of deformation and anisotropy of mechanical properties of magnesium alloys

Characterizing microscale deformation mechanisms and macroscopic tensile properties of a high strength magnesium rare-earth alloy: A combined experimental and crystal plasticity approach

Strengthening magnesium by design: Integrating alloying and dynamic processing

Influence of temperature and strain rate on flow stress behavior of twin-roll cast, rolled and heat-treated AZ31 magnesium alloys

The strain rate sensitive and anisotropic behavior of rare-earth magnesium alloy ZEK100 sheet

Influence of Alloying Materials Al, Cu, and Ca on Microstructures, Mechanical Properties, And Corrosion Resistance of Mg Alloys for Industrial Applications: A Review

Optimizing mechanical properties of magnesium alloys by philosophy of thermo-kinetic synergy: Review and outlook

On the inhomogeneous deformation behavior of magnesium alloy beam subjected to bending

Potential Magnesium Alloys for High Temperature Die Cast Automotive Applications: A Review

Deformation Mechanisms of Magnesium Alloys with Rare-Earth and Zinc Additions under Plane Strain Compression

Constitutive Behavior and Microstructure Evolution of the As-Extruded AE21 Magnesium Alloy During Hot Compression Testing

Rate-dependent transition of dislocation mechanisms in a magnesium alloy