Abstract:The diminutive additions of nickel (Ni) element have been fused to Sn-1.5Ag-0.5 mass% Cu (SAC155) lead-free solder alloy. The study was examined experimentally and computationally (using JMatPro software program) the microstructural features, thermal behavior, density, thermal diffusivity, and conductivity as well as tensile stress strain of the Sn-1.5Ag-0.5Cu-x mass %Ni (x = 0.00, 0.05, 0.10, 0.20, and 0.50) solder alloys (SAC155-xNi). The fusing additions of Ni have a little impact on the melting point of SAC155 alloy which increasing from 502 to . The microstructure of SAC155 solder alloy included coarse grains of β-Sn besides, large eutectic regions, and embedded IMCs of Ag 3 Sn and Cu 6 Sn 5 . The computed values of Gibbs free energy (G) during solidification of the β-Sn phase, Ag 3 Sn, and Sn 3 Sn 4 IMCs show the stability at , , and , respectively. The SAC155-xNi alloys involved finer β-Sn grains, large fibrous eutectic regions, (Cu,Ni) 6 Sn 5 and (Cu,Ni) 3 Sn 4 IMCs. The G of Cu 6 Sn 5 decreased from to when Ni content increased up to 0.25 mass %, then stable and steady at with more addition of Ni element. The formation of the (Cu, Ni) 6 Sn 5 and (Ni, Cu) 3 Sn 4 IMCs is motivated by the lowest Gibbs free energy, especially when Ni mass% is added to a sufficient level. The measured and computed values of specific heat at constant pressure ( C p ) of SAC155-xNi alloys show a good matching especially at lower temperatures and a little mismatch at high temperatures which decreases with increasing Ni content. The activation energy of atomic arrangement (Q) increased from 11.36 to with increasing Ni content in SAC155-xNi alloys. Thermal diffusivity (α) and conductivity (κ) of SAC155-xNi gradually decreased with increasing temperature in the range from 303 to 423 K and/or Ni content in alloys. The measured values of (κ) are slightly lower than the computed value at similar temperatures of the SAC155-xNi alloys. The decrease in (κ) may be assigned to scattering the electrons or reducing the phonon contributions due to the presence of various solute atoms and different IMCs. The results of stress-strain graphs reveal the enhancement of YS and UTS for all Ni-containing alloys. The improvement of the yield stress (YS) and ultimate tensile strength (UTS) of Ni-containing alloys is attributed to the uniform distribution of the IMCs, the reduction of β-Sn grain size, and the smoothed enlargement of the eutectic region.

Enhancing performance of Sn–Ag–Cu alloy through germanium additions: Investigating microstructure, thermal characteristics, and mechanical properties

Mechanical property optimization of Sn-1.5Ag-0.5Cu solder alloys with additions of Bi, In, and Te

Microstructure and mechanical behavior of Graphene NanoSheets enhanced lead-free Sn–0.3Ag–0.7Cu solder

Investigation of Microstructure and Mechanical Properties of SAC105 Solders with Sb, In, Ni, and Bi Additions

Intermetallic and tensile study of the newly developed Sn-2.0Ag-0.7Cu solder with addition of 0.5 wt.% zinc

The Enhanced Mechanism of 0.05 wt. % Nd Addition on High Temperature Reliability of Sn-3.8Ag-0.7Cu/Cu Solder Joint

Effect of the addition of CeO 2 nanoparticles on the microstructure and shear properties of Sn-57Bi-1Ag solder alloy

Improving the mechanical properties of high-entropy alloys via germanium addition: A focused review

Microstructural, thermal and mechanical properties of Co added Sn–0.7Cu lead-free solder alloy

Effect of trace Ge on interfacial reaction and shear strength of Sn-0.7Cu solder joints during isothermal aging and thermal cycling

The influences of reactive nanoparticles alloying on grain boundary and melting properties about Sn3.0Ag0.5Cu solder

Viscoplastic characterization of novel (Fe, Co, Te)/Bi containing Sn–3.0Ag–0.7Cu lead-free solder alloy

Atomistic analysis of the thermomechanical properties of Sn–Ag–Cu solder materials at the nanoscale with the MEAM potential

Effects of Ga addition on the microstructure and mechanical performance of Sn-58Bi based alloys and the solder joints

Effect of Ce and Sb doping on microstructure and thermal/mechanical properties of Sn-1.0Ag-0.5Cu lead-free solder

EBSD characterization of graphene nano sheet reinforced Sn–Ag solder alloy composites

Taguchi Optimization of Wetting, Thermal and Mechanical Properties of Sn-1.0wt.%Ag-0.5wt.%Cu Alloys Modified with Bi and Sb

Microstructural Examination and Thermodynamic Analysis of Sn-1.5Ag-0.5Cu-x mass% Ni Lead-Free Solder Alloys

Simultaneous strength and ductility enhancements of high thermal conductive Ag7.5Cu alloy by selective laser melting

Improvement of PbSn Solder Reliability with Ge Microalloying-Induced Optimization of Intermetallic Compounds Growth

Effect of Composition on Structural, Mechanical, and Wetting Properties of Sn-40Bi-xAg Lead-Free Solder Alloys for Green Electronics