Abstract:Effect of injection temperature and speed on the bonding strength of PA‐Al composite structure. Lightweight and high‐strength polymer–metal hybrid structures are favored for reducing material and energy consumption. In this study, carbon fiber‐reinforced polyamide 6 (CFPA) composite materials were prepared through melt blending, and 30 wt% CFPA exhibited the highest shear strength and lowest shrinkage rate among other carbon fiber contents. With pretreatments of anodizing and etching treatment, injection molded direct joining was employed to create polyamide 6 (PA)/CFPA–Aluminum alloy (Al) composites. The impacts of the injection temperature and speed on the bonding strength of the PA/CFPA–Al composite materials were investigated. The characterization results confirmed that carbon fiber doping reduces the coefficient of linear thermal expansion (CLTE) and enhances crystallization ability of PA. The higher injection temperatures and lower injection speed significantly increase the crystallinity of PA and the infiltration of the molten polymer into the nanoporous anodic aluminum oxide films. When the injection temperature was 270°C and the speed was 6 mm/s, the bonding strength of the PA–Al hybrid structure reached a maximum of 36.6 MPa. When the injection temperature was 300°C, the bonding strength of the CFPA–Al hybrid structure reached a maximum of 40.8 MPa. Adhesive parts with high shear bonding strength are critical to satisfying engineering requirements and have significant potential, particularly in polymer–metal composite structures. The polymer‐metal hybrid structure can meet the high interfacial bonding strength required in most engineering applications. Highlights Injection temperature and speed in IMDJ affect PA crystallinity. Carbon fiber doping reduces the CLTE of PA and increases the shear strength. High temperatures and low injection speeds are beneficial to adhesives. The bonding strength of PA–Al reached a maximum of 36.6 MPa. The bonding strength of CFPA–Al reached a maximum of 40.8 MPa.

Thermo-mechanically joined hybrids from carbon fiber-reinforced PA12 with die-cast alloy AlSi10Mg: how surface and interlayer design affect shear strength and fracture behavior

Joining of Aluminum and CFRP via Laser Powder Bed Fusion: Influence of Experimental Set-Up and Laser Processing on Microstructure and Mechanical Properties

Achieving high strength friction lap spot joints of carbon fiber reinforced thermosetting composite to aluminum alloy with additional thermoplastic interlayer

Ultra‐high bonding strength of carbon fiber–doped polyamide–aluminum alloy composite structure achieved by changing crystallinity

Interlaminar Shear Strength Behavior of Carbon Fiber Reinforced Aluminum Alloy Laminate

Effect of Metal Surface Topography on the Interlaminar Shear and Tensile Strength of Aluminum/Polyamide 6 Polymer-Metal-Hybrids

Effect of Laser Micro-Texturing on Laser Joining of Carbon Fiber Reinforced Thermosetting Composites to TC4 Alloy

Laser surface pre-treatment of aluminum for hybrid joints with glass fiber reinforced thermoplastics

Influence of laser texturing on the properties of fusion joints between aluminum alloys and carbon fiber reinforced thermoplastic composites

Hybrid Laser Technique for Joining of Polymer and Titanium Alloy

Novel AA7075/AA2124-SiC-17p laminated structures for aerospace applications: A Comparative study into the mechanical performance of PA6 and PA66 composite interlayers

Improving bonding strength of aluminium-PEEK hybrid metal-polymer joints by two-step laser surface treatment

Influence of Aluminum Surface Treatment on Tensile and Fatigue Behavior of Thermoplastic-Based Hybrid Laminates

Enhancing Bond Strength Between Carbon Fiber Reinforced Thermoplastic and Aluminum Alloys Through Laser Surface Treatment

Improving bonding strength of Al/CFRTP hybrid joint through modifying friction spot joining tools

Nanosecond laser ablation for improving the strength of CFRTP and aluminum alloy adhesively bonded joints

Effects of welding parameters and thermal insulation on the mechanical behavior and microstructure of friction lap-welded aluminum to glass fiber–reinforced thermoset composite with a thermoplastic PA6 interlayer

Enhancing interfacial bonding in friction stir lap welding of light metal and carbon fiber reinforced polymer composite

Mechanism of laser-inducing hierarchical surface structures improving bonding strength of metal-plastic hybrids

On the strength of joints of metal-plastic composites of hot-formed steel with an AlSi coating and a thermosetting fiber reinforced compression material

Mechanism of bonding of AA7075 aluminum alloy and CFRP during friction assisted joining