Abstract:Laser-based powder bed fusion (LPBF) is a widely utilized technique for additive manufacturing (AM) of metal components. The size of LPBF-produced parts is restricted by machine dimensions. Welding emerges as a feasible solution for connecting smaller parts generated via PBF. Nevertheless, the weldability of PBF parts differs from conventional ones due to the unique thermal history of PBF components. This paper investigated the weldability of stainless steel 316L and tensile behavior of welded samples, comparing samples produced through LPBF and the conventional wrought method. Tensile testing, grain size analysis, microhardness test, and assessment of secondary dendrite arm spacing were conducted on every welded combination of materials (AM-AM, wrought-wrought, and AM-wrought) using gas tungsten arc welding (GTAW). The findings indicate that the wrought material demonstrates a higher maximum strength (577.5 MPa) and a lower yield strength (231.7 MPa) compared to the AM material (with a maximum strength of 548.2 MPa and a yield strength of 399.9 MPa). This difference may be attributed to the annealing process applied to the wrought material, which has not been applied on the AM material. Additionally, welded wrought samples have a significantly lower tensile strength compared to non-welded samples. The wrought samples exhibit a larger average grain size (11.14 to 31.12 ) in the heat affected zone (HAZ) compared to non-heat affected regions (8.13 ). In contrast, it is found that grain coarsening does not occur in PBF samples, which exhibit a similar grain size in the HAZ (15.04 ) vs 13.97 outside of the HAZ. Larger grain sizes within the HAZ correspond to a larger reduction in tensile strength for the wrought samples, compared to PBF samples. Similar secondary dendrite arm spacing has been observed in the weld regions of both PBF and wrought materials. Microhardness test results indicated that the AM base material has the highest microhardness and gradually decreases as transitioning to the HAZ and weld region. In summary, the PBF samples exhibit less reduction of strength and ductility after welding than wrought samples. Therefore, it is determined that additively manufactured 316L stainless steel has a higher weldability than traditionally manufactured wrought 316 stainless steel.

Effect of activating fluxes on the geometry, hardness, and microstructure of 316L stainless steel in GMAW

Welding of 316L Austenitic Stainless Steel with Activated Tungsten Inert Gas Process

Effect of A-TIG Welding Process on the Weld Attributes of Type 304LN and 316LN Stainless Steels

Influence of M-TIG and A-TIG Welding Process on Microstructure and Mechanical Behavior of 409 Ferritic Stainless Steel

Effect of fluxes containing oxides on tungsten inert gas welding process

Influential Behavior Study of Fluxes during Activated Flux Tungsten Inert Gas Welding of IRSM 41 Steel

Effects of Oxide Powders as Activating Flux on AMIG 304L Welds

Effect of Induction Heat Treatment on Microstructure, Mechanical and Corrosion Properties of Stainless Steel 308L Fabricated Using Wire Arc Additive Manufacturing

Development and application of oxide-based flux powder for tungsten inert gas welding of austenitic stainless steels

Effects of gas tungsten arc welding on the mechanical properties and microstructure of 316L stainless steel by powder bed fusion

Experimental Investigation of the Impact of GMAW Welding Parameters on the Mechanical Properties of AISI 316L/ER 316L using Quaternary Shielding Gas

Effect of SiO2 and TiO2 Flux on Metallurgical and Corrosion Properties of the Activated TIG Welded AA7004 Aluminum Alloy

Effect of Active Fluxes on Penetration and Microstructure of TIG Welding

Experimental study of shielding gas concentration on mechanical properties of stainless steel alloy parts using wire and arc additive manufacturing

Influence of SiO2 Activating Flux on the Performance of Low Power Laser Welding of Stainless Steel

Microstructure and Hardness Properties of Additively Manufactured AISI 316L Welded by Tungsten Inert Gas and Laser Welding Techniques

Effect of pulse frequency on microstructure and properties of Ti-6Al-4V by ultrahigh-frequency pulse gas tungsten arc welding

Influence of oxygen content in the shielding gas chamber on mechanical properties and macroscopic structure of Ti-6Al-4V during wire arc additive manufacturing

Effect of Longitudinal Magnetic Field on the Microstructure and Properties of A-TIG Welding with Different TiO2 Coating Amounts

Influence of Metallic Oxide Nanoparticles on the Mechanical Properties of an A-TIG Welded 304L Austenitic Stainless Steel

Effects of Autogenous Gas Tungsten Arc Welding (GTAW) on Corrosion Resistance of Stainless Steel 316L