Abstract:The shield thermal neutron performance of two high boron alloyed stainless steel composite plates(HBASSCP) was studied by the method of neutron beam transmission of neutron source reactor. The testing results indicate that the shield performance of the composite material is heavily affected by the size and distribution of the boride. Although the radiationresistance of high boron alloyed stainless steel increases with boron content, but blocky and sparse hypereutectic boride will appear in matrix when boron content is high (more than 3%), and these borides are difficult to be broken during hot deformation, so the thermal neutron is easy to penetrate directly through the space and can not be absorbed effectively. The difference between the shield performance obtained from experiments and the theoretical calculation is small for HBASSCP containing hypoeutectic boride in core material, but it is great for HBASSCP containing hypereutectic boride in core material. The section of mass action which absorbed thermal neutron by steel can be raised to 0.45cm(2)/g from 0.03 cm(2)/g approximately by adding about 1% boron element into steel[1]. So whether used in pressure vessel wall or protecting biological steel plate, thermal neutron shielding plate containing boron all can reduce the heat caused by nuclear radiation, thus their wall thickness may be thinned[2,3]. However the added boron in steel have great effect on phase composition, hot working performance and mechanical properties of the materials. According to the iron-boron binary phase diagram[4], when boron content is about 3.6wt%( atoms percentage about 16.4%), eutectic reaction will happen during solidification process and eutectic organization will appear at room temperature[5]. These big brittle metal compounds is difficult to be broken refined in the deformation process, so the hot working performance and the shield neutron ability of metal will be reduced. High boron alloyed stainless composite plate, containing a middle layer of difficult-to-deformation material, was fabricated by composite casting and hot rolling process. Two kinds composite plate containing boron 2-2.5% and 4-4.5% respectively were made by this method, thermal neutron shielding tests were done and the effect of boron content on the boride morphology and shielding neutron performance were analyzed by microstructure.

Upcycling of boron bearing blast furnace slag as highly cost-effective shield for protection of neutron radiation hazard: An innovative way and proposal of shielding mechanism

Thermal neutron shielding performance and mechanism of a novel , low cost material : Boron-rich slag

The Potential Use of Boron Containing Resources for Protection Against Nuclear Radiation

Gamma ray attenuation behaviors and mechanism of boron rich slag/epoxy resin shielding composites

From Waste to Defense: Cost-efficient Upcycling of Boron Mud to Nuclear Radiation Shielding

A Novel Method of Utilization of Hot Dip Galvanizing Slag Using the Heat Waste from Itself for Protection from Radiation.

Novel Efficient Epoxy Resin Based Shielding Materials Enhanced with BN Powder Against Nuclear Radiation: A New Perspective of Shielding Performance Analysis

Neutron Shielding Properties of Boron-Containing Ore and Epoxy Composites

Effects of Boron Number Per Unit Volume on the Shielding Properties of Composites Made with Boron Ores from China

Study on the shielding performance of bismuth oxide as a spent fuel dry storage container based on Monte Carlo simulation

Study on the Properties of Boron-Containing Ores/Epoxy Composites for Slow Neutron Shielding

The Advancement of Neutron Shielding Materials for the Storage of Spent Nuclear Fuel

Designing a boron nitride polyethylene composite for shielding neutrons

Green and low-carbon upcycling of ludwigite: Prepared shields against nuclear radiation hazards and shielding mechanism

The Advancement of Neutron-Shielding Materials for the Transportation and Storage of Spent Nuclear Fuel

Preparation and Thermal/Fast Neutron Shielding Properties of Novel Boron Containing Ore Composites

Shield performance of high boron alloyed stainless steel composite plate

Study on a High-Boron-Content Stainless Steel Composite for Nuclear Radiation

Design and performance of a novel neutron shielding composite materials based on AlSi10Mg porous structure fabricated by laser powder bed fusion

Shielding properties of boron-containing ores composites for 1 keV, 1e V and 0.0253 eV neutron

Shielding Properties of Boron-Containing Ores Composites for 1 Kev,1 Ev and 0.025 3 Ev Neutron