Abstract:There are multiple routes to prepare semi-solid slurries with a globular microstructure for semi-solid forming. The variations in the microstructure of semi-solid slurries prepared using different routes may lead to significant differences in the flow behavior and mechanical properties of rheo-diecasting parts. Therefore, it is crucial to have a comprehensive understanding of the microstructure evolution associated with different slurry preparation routes and their resulting effects. In this study, the gas-induced semi-solid process (GISS) and the swirl enthalpy equilibrium device (SEED) routes were employed to prepare semi-solid Al-Si-Mg slurries for their simplicity and productivity in potential industrial applications. The prepared slurries were then injected into the shoot sleeves of a high-pressure die casting (HPDC) machine to produce tensile test bars. Subsequently, the bars underwent T6 treatment to enhance their mechanical properties. The microstructure, segregation, and mechanical properties of the samples were investigated and compared with those of conventional HPDC. The results indicated that the GISS and SEED can produce semi-solid slurries containing a spherical α-Al primary phase, as opposed to the dendritic structure commonly found in conventional castings. The liquid fraction had a significant effect on the flow behavior, resulting in variations in liquid segregation and mechanical properties. It was observed that a higher solid fraction (>75%) had a suppressing effect on surface liquid segregation. In addition, the tendency for liquid segregation gradually increased along the filling direction due to the special flow behavior of the semi-solid slurry with a low solid fraction. Furthermore, under the same die-casting process parameters, the conventional HPDC samples exhibit higher yield stress (139 ± 3 MPa) compared to SEED-HPDC and GISS-HPDC samples, which may be attributed to the small grain size and the distribution of eutectic phases. After undergoing the T6 treatment, both SEED-HPDC and GISS-HPDC samples showed a significant improvement in yield and tensile strength. These improvements are a result of solution and precipitation strengthening effects as well as the spheroidization of the eutectic Si phase. Moreover, the heat-treated SEED-HPDC samples demonstrate higher ultimate strength (336 ± 5 MPa) and elongation (13.7 ± 0.3%) in comparison to the GISS-HPDC samples (307 ± 4 MPa, 8.8 ± 0.2%) after heat treatment, mainly due to their low porosity density. These findings suggest that both GISS-HPDC and SEED-HPDC processes can be utilized to produce parts with favorable mechanical properties by implementing appropriate heat treatments. However, further investigation is required to control the porosities of GISS-HPDC samples during heat treatment.

Entrainment defects in semi-solid A356 aluminum alloy treated by ICTE process

On-line Preparation Technology of Semi-Solid Slurry of A356.2 Alloy

Influences of Master Alloys and Their Preparation Conditions on Microstructures of Semi-solid A356 Alloy Slurries

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

New technique for preparing A356 alloy semisolid slurry and its rheo-diecast microstructure and properties

Preparation of Semi-Solid A356 Al Alloy Slurry by Repeated Heating-Cooling Method with Elliptical-Twisted Tubes

Improving element uniformity and mechanical properties of Al–Mg–Si alloy fabricated by twin roll casting with superheat melt treatment

Microstructure, segregation and mechanical properties of A356 alloy components fabricated by rheo-HPDC combined with the Swirled Enthalpy Equilibration Device (SEED) process

Rheological Modeling of 7075 Aluminum Alloy Semi-Solid Slurry and its Application in the Simulation of SEED Rheocasting Process

Numerical simulation study on solidification process of titanium slab ingot by electron beam cold hearth melting

Effect of Mold Electromagnetic Stirring and Final Electromagnetic Stirring on the Solidification Structure and Macrosegregation in Bloom Continuous Casting

Experimental Studies on Rheocasting Processing of A356 Alloy

Simulation prediction of CP-Ti slab ingot solidification structure based on the CAFE method

Using the Phase Field Method to Investigate Microstructural Evolution of Semi-Solid 357.0 Slurries

Rheologic Properties of Aluminum Alloy A356 Bille ts Produced by Semisolid Continuous Casting Process

Electrical-thermal-mechanical coupled modeling and simulation on deformation behaviors of Ti6554 alloy in electrically-assisted micro-tension

Microstructure characteristics and strengthening mechanism of semisolid CuSn10P1 alloys

A Comparative Study on Microstructure, Segregation, and Mechanical Properties of Al-Si-Mg Alloy Parts Processed by GISS-HPDC and SEED-HPDC

Simulation and Study of Influencing Factors on the Solidification Microstructure of Hazelett Continuous Casting Slabs Using CAFE Model

Semi-Solid Slurries for Rheocasting of Hypoeutectic Al-Si-X Alloys Produced by Self-Stirring in Serpentine Channels