Abstract:Taking into account the local stresses resulting from the primary twinning with transformation strains, the competition between double twinning {10–11}–{10–12} and (10–12)–(–1012) (CDTW and EDTW) is theoretically modeled. Using electron backscatter diffraction technique, the statistical fractions, thickness-length ratios and their critical values of CDTW and EDTW within grains of as-cast AZ31 magnesium alloy sheets at the low strain stage of hot rolling processing are obtained to validate the theoretical results. In addition, the competition between the DTW and twin intersection are also discussed in detail. The results show that: (1) The secondary twin growth complies with the classical Hall-Petch relationship. Due to the difference in the driving forces resulting from different transformation strains between the primary extension and contraction twinning, the secondary extension twin of EDTW is more difficult to grow compared to that of CDTW for primary twin bands with small thickness-length ratios, which is contrary to the regulation for primary twin bands with large thickness-length ratios; (2) The greater the thickness-length ratio of the primary twinning is, the smaller the critical shear stress of the secondary twinning is. This is opposite to the effect of thickness-length ratio on the critical shear stress of the incident twinning in the twin intersection. It is indicated that the thickening of the primary twinning provides the higher driving force for the formation of DTW, however hinders the twin intersection more evidently; (3) Within coarse grains, at the low strain stage, the formation of DTW can dominantly induce dynamic recrystallization and continue plastic deformation, while the stress concentration resulting from the twin intersection is inclined to cause brittle fracture. Therefore, based on the effect of the local stress, the selection mechanism of the thickness-length ratio on the DTW and twin intersection is of great significance to determining the plastic performance of magnesium alloys during hot working. In the current study, massive control factors of the thickness-length ratio of the primary twinning are concluded, which provides some corresponding schemes of material design.

Detwinning of AZ31 magnesium alloy during in situ tension

Towards Understanding {10-11}-{10-12} Secondary Twinning Behaviors in AZ31 Magnesium Alloy during Fatigue Deformation

Twinning of AZ31 Magnesium Alloy Analyzed by EBSD Technique

Study on twinning behaviors during multi-directional compression for AZ31 magnesium alloy by EBSD

Three-dimensional study of grain scale tensile twinning activity in magnesium: A combination of microstructure characterization and mechanical modeling

Three-dimensional study of grain scale tensile twinning activity in Mg: A combination of microstructure characterization and mechanical modeling

Twinning and dynamic recrystallization behaviors during inchoate deformation of pre-twinned AZ31 Mg alloy sheet at elevated temperatures

Study of Twin Behavior During Uniaxial Compression of Az31 Magnesium Alloy

Tension induced detwinning of hierarchically twinned non-modulated martensite in Ni-Mn-Ga alloys

In Situ Monitoring of Dislocation, Twinning, and Detwinning Modes in an Extruded Magnesium Alloy under Cyclic Loading Conditions

Towards understanding double extension twinning behaviors in magnesium alloy during uniaxial tension deformation

Quantitative investigation on the {10–12} twinning-detwinning behavior and twinning transfer of an extruded Mg-2.8Y sheet during compression-tension loading via quasi-in-situ EBSD observation

The Dislocation-Twin Interaction and Evolution of Twin Boundary in AZ31 Mg Alloy

The evolution of local stress during deformation twinning in a Mg-Gd-Y-Zn alloy

Influence of Local Strain on Twinning Behavior During Compression of AZ31 Magnesium Alloy

Effect of Local Stresses of Primary Twinning on Double Twinning, Twin Intersection and Their Competition

Transmission electron microscopy observation of a deformation twin in TWIP steel by an ex situ tensile test

Study on the Twinning/De-twining Behavior of Different Types of Twin–Twin Interaction via Experiments and Molecular Dynamics Simulation

Effect of Slip on Detwinning Behavior During Multi-Direction Compression of A Wrought Magnesium Alloy

Unveiling the ductility enhancement mechanisms in AZ31 magnesium alloy achieved via shear strain-assisted twin orientation regulation

Competition Between Shear Localization and Tensile Detwinning in Twinned Nanowires