Abstract:Li-rich and Mn-based layered oxides are the most promising candidates for next-generation high energy density cathode materials. However, inherent problems including poor rate performance, continuous capacity degradation, and voltage fading hinder their commercial utilization. Herein, a lattice- and interfacial-modified Li1.2Mn0.54Co0.13Ni0.13O2 with a pristine-layered bulk structure, Na- and S-doped transition phase, and epitaxially grown Na2Mn (SO4)2 (C2/c symmetry) layer were constructed by Na2S treatment. The monoclinic Na2Mn(SO4)2 not only acts as an interface protective layer, alleviating the harmful electrode–electrolyte reactions, but also promotes formation of oxygen vacancy in the layered structure, enhancing reversibility of oxygen redox. The Na and S surface lattice doping leads to enhanced Li+ diffusion and alleviates the chance of oxygen release. With the positive effects provided by the stable interfacial layer and lattice modification, the modified cathodes with moderate Na2S treatment shows alleviated capacity and voltage decay and enhanced electrochemical kinetics. Especially, the washed cathode with 3 wt % Na2S treatment delivers a discharge specific capacity of 305 at 0.1 C and 219 mA h g–1 at 1 C, as well as 93.15% capacity retention and 88.20% voltage retention after 200 cycles at 1 C.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c08797?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c08797</a>.Rietveld refinement patterns using powder XRD of LMCN, LMCN-NS1, LMCN-NS3, LMCN-NS6, and WLMCN-NS3 samples; summary of structural refinement of the samples by a Rietveld method; HRTEM and FFT images of LMCN-NS3; the cross-section SEM image and corresponding Ni, Co, Mn, Na, S, and O distribution on the cross-sectioned particle for LMCN-NS3; EPR spectra of LMCN and LMCN-NS3; initial charge/discharge profiles of LMCN, LMCN-NS1, LMCN-NS3, and LMCN-NS6 at 0.1 C; cyclic performance of LMCN, LMCN-NS1, LMCN-NS3, and LMCN-NS6 at 1 C; initial charge/discharge profiles of LMCN, LMCN-N3, LMCN-S3, and LMCN-NS3 at 0.1 C; rate capability of LMCN, LMCN-N3, LMCN-S3, and LMCN-NS3; cyclic performance of LMCN, LMCN-N3, LMCN-S3, and LMCN-NS3 at 1 C; average voltage of discharging process for LMCN, LMCN-NS3, and W LMCN-NS3 at 1 C; XPS spectra of Mn 2p, Ni 2p, Co 2p, S 2p, Na 1s, and O 1s for LMCN and WLMCN-NS3 with different etching times; CV curves of the LMCN and WLMCN-NS3; and corresponding detailed data of Rs, Rct, σω, and DLi+ of the LMCN and WLMCN-NS3, respectively, for 1st and 300th (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c08797/suppl_file/am0c08797_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Thermally Aged Li–Mn–O Cathode with Stabilized Hybrid Cation and Anion Redox

Stabilizing Anionic Redox Chemistry in a Mn‐Based Layered Oxide Cathode Constructed by Li‐Deficient Pristine State

Modulating the local electronic structure via Al substitution to enhance the electrochemical performance of Li-rich Mn-based cathode materials

Na 2 S Treatment and Coherent Interface Modification of the Li-Rich Cathode to Address Capacity and Voltage Decay

Exploit Li2MnO3 Activity by Two Phase Coexistence at Atomic Level Towards High Performance Mn-based Co-free Li-rich Cathodes

Stabilized Co‐Free Li‐Rich Oxide Cathode Particles with an Artificial Surface Prereconstruction

Enhanced Cathode Performance: Mixed Al 2 O 3 and LiAlO 2 Coating of Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2

Tuning Both Anionic and Cationic Redox Chemistry of Li-Rich Li 1.2 Mn 0.6 Ni 0.2 O 2 via a “Three-in-One” Strategy

Exploit Li 2 MnO 3 activity by two phase coexistence at atomic level towards high performance Mn-based Co-free Li-rich cathodes

Facile Synthesis of Hierarchical Porous Three-Dimensional Free-Standing MnCo2O4 Cathodes for Long-Life Li-O2 Batteries.

Stabilizing a Li–Mn–O Cathode by Blocking Lattice O Migration through a Nanoscale Phase Complex

Electrochemical Behaviours and Structure Evolution of High Capacity Li1.2Cr0.4Mn0.4O2 Cathode Material in a Wide Voltage Range

High Performance Li[Li0.2Ni0.13Co0.13Mn0.54](BO4)0.75x(BO3)0.25xO2-3.75x Cathode with Polyanion for Li-Ion Batteries

Enhancing the Stability of Li-Rich Mn-Based Oxide Cathodes Through Surface High-Entropy Strategy

Constructing Targeted Strong Nb4d‐O2p‐Li2s Configurations to Obtain Excellent Energy Density and Long Life for Li‐rich Cathodes

Mild Lithium‐Rich Manganese‐Based Cathodes with the Optimal Activation of Li2MnO3 for Stable and High Capacity Lithium‐Ion Batteries

Na-substitution induced oxygen vacancy achieving high transition metal capacity in commercial Li-rich cathode

Improving the stability of P2-type NaMn2/3Ni1/3O2 via phasic intergrowth induced by Li-ion substitution

Accelerating the Activation of Li2MnO3 in Li-rich High-Mn Cathodes to Improve Its Electrochemical Performance.

Constructing a robust Li-rich Mn-based oxide cathode with oxygen vacancies and strong B-O bonds by BN treatment

In Situ Induced Lattice‐Matched Interfacial Oxygen‐Passivation‐Layer Endowing Li‐Rich and Mn‐Based Cathodes with Ultralong Life