Abstract:Because of the global fossil energy crisis and environmental pollution problems, the efficient use of green, renewable,and clean energy has become a major trend. Mechanical energy is considered an ideal alternative energy source because of its abundance, accessibility, and non-polluting characteristics. A piezoelectric nanogenerator（PENG） can convert environmental mechanical energy into electrical energy to power electronic devices. However, conventional piezoelectric materials must induce dipole alignment by electrical polarization to obtain piezoelectric properties, which substantially increases the cost and energy consumption of device preparation. Meanwhile, depolarization occurs when the external electric field is removed, which severely affects the performance of the piezoelectric material. In this study, PVDF nanofiber film is prepared using the electrospinning method. The PVDF dipole is rearranged to achieve in situ polarization by a strong electric field and stretching force generated by the electrospinning process. The PVDF nanofiber film process has a high electroactive β-phase content of 78.7%, which is the main contributor to the piezoelectric properties. The PENG constructed based on this film achieves direct conversion of mechanical energy to electrical energy, greatly improving energy use. The open-circuit output voltage of the thin film PENG prepared based on the electrostatic spinning method is 1.6 V, and the short-circuit output current is 0.14 μA, which are 4.5- and 2.6-fold higher than those prepared using the spin-coating method, respectively. The PVDF–PENG can charge a 1-μF capacitor to 2 V through a bridge rectifier after 60 s of human finger tapping.The power density of the PVDF–PENG is analyzed by measuring the electrical parameters at both ends of the resistor. The maximum output power is 0.03 μW at an applied load of 200 MΩ. More electrical energy can be obtained based on the PVDF–PENG, which further illustrates its possibilities and reliability in practical applications. Further, the PVDF –PENG maintains approximately 100%output capacity after 2000 consecutive cycles of compression, verifying its long-term stable service capability. Finally, the energy collected from the mechanical energy of human motion by the PVDF–PENG is explored to drive low-power consumer electronics. Six commercial LEDs are lit by using a large PENG without using any storage device. In addition, a bridge rectifier is used to charge a 2.2-μF capacitor, which successfully lights up a commercial electronic watch.

Enhancing the piezoelectric coefficient of SrTiO 3 nanocubes and PVDF film deposited by supersonic spraying for energy-harvesting nanogenerators

Flexible piezoelectric energy-harvesting nanogenerator using supersonically sprayed polyvinylidene fluoride and iron oxide nanocubes

Supersonically Sprayed Flexible ZnO/PVDF Composite Films with Enhanced Piezoelectricity for Energy Harvesting and Storage

Enhanced Piezoelectric Energy Harvester by Employing Freestanding Single‐Crystal BaTiO3 Films in PVDF‐TrFE Based Composites

Mechanical Energy Harvesting and Specific Potential Distribution of a Flexible Piezoelectric Nanogenerator Based on 2-D BaTiO 3 -Oriented Polycrystals

Textured CsPbI3 Nanorods Composite Fibers for Stable High Output Piezoelectric Energy Harvester

Supersonically Sprayed Pvdf and Zno Nanoflowers with Built-In Nanocuboids for Wearable Piezoelectric Nanogenerators

Screen Printing of Surface-Modified Barium Titanate/Polyvinylidene Fluoride Nanocomposites for High-Performance Flexible Piezoelectric Nanogenerators

Interface modulated 0-D piezoceramic nanoparticles/PDMS based piezoelectric composites for highly efficient energy harvesting application

Piezoelectric Nanogenerator Based on Lead-Free Flexible PVDF-Barium Titanate Composite Films for Driving Low Power Electronics

Synergistic Effect of Graphene Nanosheet and BaTiO3 Nanoparticles on Performance Enhancement of Electrospun PVDF Nanofiber Mat for Flexible Piezoelectric Nanogenerators

Piezoelectric Nanogenerators Based on Electrospun PVDF-Coated Mats Composed of Multilayer Polymer-Coated BaTiO3 Nanowires

Flexible Piezoelectric Nanogenerators Based on P(VDF-TrFE)/CsPbBr 3 Quantum Dot Composite Films

Hybrid Piezoelectric/Triboelectric Wearable Nanogenerator Based on Stretchable PVDF-PDMS Composite Films

Flexible Composites with Rare-Earth Element Doped Polycrystalline Particles for Piezoelectric Nanogenerators

Piezoelectric Thin Film on Glass Fiber Fabric with Structural Hierarchy: an Approach to High-Performance, Superflexible, Cost-Effective, and Large-Scale Nanogenerators

3D Printing Enhanced Piezoelectricity of MXene/P(VDF-TrFE) Composites for Energy Harvesting and Force Sensing

Performance Enhancement of Flexible Piezoelectric Nanogenerator via Doping and Rational 3D Structure Design For Self‐Powered Mechanosensational System

Controllable Core-Shell BaTiO<sub>3</sub>@Carbon Nanoparticle-Enabled P(VDF-TrFE) Composites: A Cost-Effective Approach to High-Performance Piezoelectric Nanogenerators

Construction of a High-Efficiency Piezoelectric Nanogenerator Based on in Situ Polarization of PVDF Nanofiber Films by Electrospinning

Interface-engineered composite nanofibers for boosting piezoelectric outputs of polymeric nanogenerators