Abstract:Due to their low-temperature deposition, high mobility (>10 cm2/V·s), and electrical conductivity, amorphous ionic oxide semiconductors (AIOSs) have received much attention for their applications in flexible and/or organic electro-optical devices. Here, we report on a study of the flexibility of CdO-In2O3 alloy thin films, deposited on a polyethylene terephthalate (PET) substrate by radio frequency magnetron sputtering at room temperature. Cd1–xInxO1+δ alloys with the composition of x > 0.6 are amorphous, exhibiting a high electron mobility of 40–50 cm2/V·s, a low resistivity of ∼3 × 10–4 Ω·cm, and high transmittance over a wide spectral window of 350 to >1600 nm. The flexibility of both crystalline and amorphous Cd1–xInxO1+δ films on the PET substrate was investigated by measuring their electrical resistivity after both compressive and tensile bending with a range of bending radii and repeated bending cycles. Under both compressive and tensile bending with Rb = 16.5 mm, no significant degradation was observed for both the crystalline and amorphous films up to 300 bending cycles. For a smaller bending radius, the amorphous film shows much less electrical degradation than the crystalline films under compressive bending due to less film delamination at the bending sites. On the other hand, for a small bending radius (<16 mm), both crystalline and amorphous films degrade after repeated tensile bending, most likely due to the development of microcracks in the films. To demonstrate the application of amorphous Cd1–xInxO1+δ alloy in photovoltaics, we fabricated perovskite and bulk-heterojunction organic solar cells (OSCs) on glass and flexible PET utilizing amorphous Cd1–xInxO1+δ layers as transparent electrodes. The organic–inorganic hybrid perovskite solar cells (PSCs) exhibit a power conversion efficiency (PCE) of ∼11 to 12% under both front and back illumination, demonstrating good bifacial performance with bifaciality factor >90%. The OSCs fabricated on an amorphous Cd1–xInxO1+δ-coated flexible PET substrate achieve a promising PCE of 12.06%. Our results strongly suggest the technological potentials of amorphous Cd1–xInxO1+δ as a reliable and effective transparent conducting material for flexible and organic optoelectronic devices.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c14722.AFM images of Cd1–xInxO1+δ films before and after bending; schematic diagram of the van der Pauw sample configuration for the electrical measurements; and fabricating process of solar cells (PDF)This article has not yet been cited by other publications.

Amorphous metal thin film electrode for mechanically robust charge collection of organic photovoltaics

High Electrical Conductivity and Carrier Mobility in Ocvd PEDOT Thin Films by Engineered Crystallization and Acid Treatment

Metallic amorphous alloy for long-term stable electrodes in organic sensors and photovoltaics

Biomimetic Electrodes for Flexible Organic Solar Cells with Efficiencies over 16%

Electrode stress passivation via oxide titanium amorphous interlayer for flexible non-fullerene organic photovoltaics

Recent Progress on Emerging Transparent Metallic Electrodes for Flexible Organic and Perovskite Photovoltaics

Flexible Silver Grid/Pedot:Pss Hybrid Electrodes for Large Area Inverted Polymer Solar Cells

Highly Flexible All‐Polymer Solar Cells Processed Without Post‐Treatment Achieving 13.56% Efficiency

Stretchable and transparent nanopillar arrays for high-performance ultra-flexible organic photovoltaics

Flexible organic photovoltaics based on water-processed silver nanowire electrodes

Flexible High‐Performance and Solution‐Processed Organic Photovoltaics with Robust Mechanical Stability

Flexibility of Room-Temperature-Synthesized Amorphous CdO-In 2 O 3 Alloy Films and Their Application as Transparent Conductors in Solar Cells

Highly transparent and conductive metal oxide/metal/polymer composite electrodes for high-efficiency flexible organic light-emitting devices

Embedded Nickel‐Mesh Transparent Electrodes for Highly Efficient and Mechanically Stable Flexible Perovskite Photovoltaics: Toward a Portable Mobile Energy Source

Challenging Bendable Organic Single Crystal and Transistor Arrays with High Mobility and Durability towards Flexible Electronics

12.42% Monolithic 25.42 cm 2 Flexible Organic Solar Cells Enabled by an Amorphous ITO‐Modified Metal Grid Electrode

Preparation of flexible organic solar cells with highly conductive and transparent metal-oxide multilayer electrodes based on silver oxide

Highly conductive and flexible electrodes based on ultrathin aluminum-doped zinc oxide epitaxial films

1D:2D Structured AgNW:MXene Composite Transparent Electrode with High Mechanical Robustness for Flexible Photovoltaics

High‐Efficiency and Mechanically Robust All‐Polymer Organic Photovoltaic Cells Enabled by Optimized Fibril Network Morphology

Ductile Oligomeric Acceptor‐Modified Flexible Organic Solar Cells Show Excellent Mechanical Robustness and Near 18% Efficiency