Abstract:Recent developments in hybrid organic–inorganic lead halide perovskite solar cells (PSCs) have shown that use of a 2-dimensional (2D) perovskite capping layer on a 3D perovskite absorber layer (3D/2D PSCs) results in substantially improved environmental stability of the devices. However, in these 3D/2D PSC structures the poor charge transporting properties through the 2D layer hinder device performance, particularly for thicker 2D layers. Here, we report a facile method that overcomes some of the inherent challenges in using such 2D capping layers through the introduction of 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ) as a molecular additive into the 2D layer. It is found that this additive undergoes partial charge transfer with the perovskite layer to provide a passivation effect, which also modifies the crystalline domain sizes of the 2D perovskite. PSCs incorporating a F4TCNQ-modified 2D capping layer grown in situ on top of the 3D Cs/MA/FA mixed-cation perovskite absorber layer display modified interfacial characteristics that yield improved charge extraction and reduced charge recombination compared with 3D/2D PSCs comprising an unmodified 2D capping layer. This modification results in 3D/2D PSCs for which the maximum power conversion efficiency is increased to more than 20% compared with 18.2% for unmodified 2D capping layers.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.0c00553.Fitting parameters of PL decay, SEM images with EDX mapping, GIWAXS patterns, GA-FTIR spectra, UV–vis spectra, steady-state PL spectra, PESA spectra, and contact angle images of perovskite films; J–V curves, IPCE spectra, raw TPC curves, and impedance Nyquist plots with fitting parameters of devices; device parameters of stability testing; contact angle characterization of perovskite films (PDF)This article has not yet been cited by other publications.

Multifunctional 2D perovskite capping layer using cyclohexylmethylammonium bromide for highly efficient and stable perovskite solar cells

Two birds with one stone: Simultaneous realization of constructed 3D/2D heterojunction and p-doping of hole transport layer for highly efficient and stable perovskite solar cells

Facilitate hole transport with thin 2D perovskite capping layer to passivate interface defects of 3D perovskite solar cells using PEABr

Toward desirable 2D/3D hybrid perovskite films for solar cell application with additive engineering approach

Surface Terminated 3D/2D Heterojunction Enables Efficient and Stable Perovskite Solar Cells

Enhancement of 3D/2D Perovskite Solar Cells Using an F4TCNQ Molecular Additive

A 2D/3D heterojunction engineering for carbon-based hole-transport-layer-free perovskite solar cells

Enhanced photovoltage and stability of perovskite photovoltaics enabled by a cyclohexylmethylammonium iodide-based 2D perovskite passivation layer

Constructing 2D passivation layer on perovskites based on 3-chlorobenzylamine enables efficient and stable perovskite solar cells

Highly efficient and stable perovskite solar cells enabled by low-dimensional perovskitoids

In Situ Formation of a 2D/3D Heterostructure for Efficient and Stable CsPbI2Br Solar Cells

Introduction of Hydrophobic Ammonium Salts with Halogen Functional Groups for High‐Efficiency and Stable 2D/3D Perovskite Solar Cells

Magnetic Field‐Assisted Interface Embedding Strategy to Construct 2D/3D Composite Structure for Stable Perovskite Solar Cells with Efficiency Over 24%

Synergistic Passivation With Phenylpropylammonium Bromide for Efficient Inverted Perovskite Solar Cells

2D/3D heterostructured CsPbI2Br solar cells: a choice for a monolithic all-perovskite tandem device

Formation of Low-Dimensional Double Perovskite Layers by ABS and PEAI Sequential Treatment for Achieving High-Performance CsPbI 3 Solar Cells

Bulk passivation and suppressing non-radiative recombination loss in a 3D all-inorganic CsPbIBr2 perovskite solar cell via a 2D layered perovskite framework

Formation of Low-Dimensional Double Perovskite Layers by ABS and PEAI Sequential Treatment for Achieving High-Performance CsPbI<sub>3</sub> Solar Cells

In‐Situ Self‐Assembly Dipole Shielding Layer Toward Efficient and Stable Inorganic Perovskite Solar Cells

In Situ Growth of a Robust 1D Capping Layer for Stable and Efficient CsPbI3 Perovskite Solar Cells Without Hole Transporter

Construction of 2d/3d/2d‐structured Perovskite for High‐Performance and Stable Solar Cells