Tuning the intermediate reaction barriers by a CuPd catalyst to improve the selectivity of CO2 electroreduction to C2 products

Li Zhu,Yiyang Lin,Kang Liu,Emiliano Cortés,Hongmei Li,Junhua Hu,Akira Yamaguchi,Xiaoliang Liu,Masahiro Miyauchi,Junwei Fu,Min Liu

DOI: https://doi.org/10.1016/s1872-2067(20)63754-8

IF: 16.5

2021-09-01

Chinese Journal of Catalysis

Abstract:Electrochemical CO₂ reduction is a promising strategy for the utilization of CO₂ and intermittent excess electricity. Cu is the only single metal catalyst that can electrochemically convert CO₂ into multicarbon products. However, Cu exhibits an unfavorable activity and selectivity for the generation of C2 products because of the insufficient amount of CO* provided for the C-C coupling. Based on the strong CO₂ adsorption and ultrafast reaction kinetics of CO* formation on Pd, an intimate CuPd(100) interface was designed to lower the intermediate reaction barriers and improve the efficiency of C2 product formation. Density functional theory (DFT) calculations showed that the CuPd(100) interface enhanced the CO₂ adsorption and decreased the CO₂* hydrogenation energy barrier, which was beneficial for the C-C coupling. The potential-determining step (PDS) barrier of CO₂ to C2 products on the CuPd(100) interface was 0.61 eV, which was lower than that on Cu(100) (0.72 eV). Encouraged by the DFT calculation results, the CuPd(100) interface catalyst was prepared by a facile chemical solution method and characterized by transmission electron microscopy. CO₂ temperature-programmed desorption and gas sensor experiments further confirmed the enhancement of the CO₂ adsorption and CO₂* hydrogenation ability of the CuPd(100) interface catalyst. Specifically, the obtained CuPd(100) interface catalyst exhibited a C2 Faradaic efficiency of 50.3% ± 1.2% at −1.4 V_RHE in 0.1 M KHCO₃, which was 2.1 times higher than that of the Cu catalyst (23.6% ± 1.5%). This study provides the basis for the rational design of Cu-based electrocatalysts for the generation of multicarbon products by fine-tuning the intermediate reaction barriers.A CuPd(100) catalyst was designed and fabricated to improve the selectivity of the electroreduction of CO₂ to C2 products by tuning the CO₂ adsorption ability and intermediate reaction barriers.

chemistry, physical,engineering, chemical, applied

What problem does this paper attempt to address?

### Problems the Paper Aims to Solve

The main objective of this paper is to improve the selectivity and efficiency of CO₂ electroreduction to produce C₂ products (such as ethane and ethanol) by designing a CuPd(100) interface catalyst.

#### Specific Problems:
1. **Improving the selectivity of CO₂ electroreduction to produce C₂ products**: Cu catalysts exhibit low selectivity for C₂ products during the electrochemical reduction of CO₂ because the amount of CO* (CO adsorbed on the catalyst surface) provided is insufficient, leading to ineffective C-C coupling steps.
2. **Reducing intermediate reaction barriers**: By introducing Pd components to form a CuPd(100) interface, CO₂ adsorption can be enhanced and the barrier for CO₂* hydrogenation can be lowered, thereby facilitating C-C coupling.
3. **Theoretical and experimental validation**: Using density functional theory (DFT) calculations to predict the performance of the CuPd(100) interface catalyst, and experimentally preparing and characterizing the catalyst to verify its effectiveness in actual electrochemical reactions.

#### Main Contributions:
- **Theoretical prediction**: DFT calculations indicate that the CuPd(100) interface catalyst can significantly enhance CO₂ adsorption and lower the barrier for CO₂* hydrogenation.
- **Experimental validation**: The CuPd(100) interface catalyst is prepared using a chemical solution method and characterized using techniques such as transmission electron microscopy (TEM).
- **Electrochemical performance testing**: Under electrochemical conditions, the CuPd(100) interface catalyst exhibits a higher Faradaic efficiency for C₂ products (50.3%), which is approximately 2.1 times higher than that of the pure Cu catalyst (23.6%).

In summary, this paper aims to optimize the selectivity and efficiency of C₂ product generation in the CO₂ electroreduction process by designing a CuPd(100) interface catalyst, providing a new strategy for developing efficient Cu-based electrocatalysts.