Abstract:Reducing heat losses is an important factor in improving the performance of district heating networks. High heat losses are sometimes experienced in UK district heating networks and this is often as a result of poor design, partly due to oversized pipes. To provide additional guidance to designers on this issue, this paper proposes a set of maximum pipe diameters to be used for a given maximum flow rate to reduce the risk of oversizing and high heat losses. It was found that the optimised velocities are higher than those given in CIBSE CP1 Heat Networks Code of Practice and adopting these will result in smaller pipe diameters and lower operational and capital costs. The methodology used in this paper is based on minimising the total operational energy. The flow and return optimised pipe diameters are calculated for different scenarios which include variations in the pipe material, insulation thickness, water temperature and ambient environment. It was found that the optimised velocity in every scenario remains relatively constant with a varying pipe diameter. This paper shows that the operational cost of a DH network can be reduced when selecting the recommended maximum pipe diameter, compared to commonly used sizing criteria. Further savings can be achieved if the flow and return pipe are sized separately; to minimise operational energy of both flow and return pipes, the return pipe should be sized for a lower velocity. This paper also explores particular questions of interest: A range of insulation thicknesses. Benefit from using a variable flow temperature and to supply the flow at 90°C at peak times instead of a constant temperature at 70°C. A comparison between steel and plastic pipes which have different roughness coefficients. Optimised differential pressure drop per unit length in both flow and return pipes. Maximum distance occurring before measuring a temperature loss and pressure drop of 1°C and 1 bar, respectively, at peak load. However, this paper does not take into account any potential benefits that a lower flow temperature might have in reducing heat production costs or a lower return temperature might have in enhanced heat recovery, or that lower temperatures may enable use of plastic carrier pipes. Such matters are site specific but should be included in any similar pipe sizing analysis and operating temperature optimisation carried out for an actual scheme. Practical application: Optimising maximum pipe diameters is necessary to improve the viability of district heating systems. The current guidance for designers is not considered optimal and this paper suggests a new methodology to size pipes to reduce both the heat losses and the operational cost. This paper also gives guidance to sustainability engineers to assess the performance of 90/40°C, 70/40°C and 60/30°C district heating networks; 70°C was assumed to be the minimum acceptable flow temperature in the network to enable domestic hot water to be heated to a safe temperature of 60°C for storage; 40°C was the used return temperature to be in line with the CIBSE Code of Practice CP1 stating in Objective 3.5 that best practice should achieve return temperatures below 40°C for a scheme supplying heat to new buildings. A 90/40°C DH network performance when increasing the flow temperature was then compared to the performance of a 70/40°C system. Finally, a 60/30°C system was also analysed to investigate the benefit from operating a DH network complying with the 4th generation of DH network temperatures that encourages minimal exergy destruction from the network to the end user.

Heat loss optimization and economic evaluation of a new fourth generation district heating triple pipe system

A Data-driven Model of Pipe Diameter and Insulation Thickness Optimization for District Heating Systems

A new type of two-supply, one-return, triple pipe-structured heat loss model based on a low temperature district heating system

Online Energy-Loss Analysis System for Thermal Power Generating Unit of Piping-Main Scheme

Optimising pipe sizing and operating temperatures for district heating networks to minimise operational energy consumption

Construction and analysis of a district heating / cooling network system based on thermal bus

Optimization of Insulation Arrangement Parameters and Technical-Economic Evaluation of Inner Pipe in Deep Borehole Heat Exchanger

Distinguish between the economic optimal and lowest distribution temperatures for heat-prosumer-based district heating systems with short-term thermal energy storage

Analysis of Operation Regulation on Delay Time in Long-Distance Heating Pipe Systems for Practical Engineering

Study on the Flow in the Pipelines of the Support System of Circulating Fluidized Bed

The Influence of Central Regulation Methods Upon Annual Heat Loss in Heating Network

Pipe Insulation Evaluation for Low-Temperature District Heating Implementation in South Korea

Optimization of the configuration and flexible operation of the pipe-embedded floor heating with low-temperature district heating

Power Flow Model and Algorithm of Combined Power and Heat System Considering Heat Loss in Return Pipe Network

Dynamic modeling and intelligent heating strategies of district heating system based on the standardized thermal resistance

Thermo-economic Analysis for Directly-buried Pipes Insulation of District Heating Piping Systems☆

Systematic Optimization for the Utilization of Low-Temperature Industrial Excess Heat for District Heating

Life cycle cost approach involving steam transport model for insulation thickness optimization of steam pipes

Online hydraulic calculation and operation optimization of industrial steam heating networks considering heat dissipation in pipes

Thermo-Economic Assessment on Insulation Conditions of the Buried Heating Pipeline for District Heating

Economic topology optimization of District Heating Networks using a pipe penalization approach