Abstract:Background There is a quest of novel functional and reliable platforms for enhancing the efficiency of microextraction approaches in troublesome matrices, such as industrial wastewaters. 3D printing has been proven superb in the analytical field to act as the springboard of microscale extraction approaches. Results In this work, low-force stereolithography (SL) was exploited for 3D printing and prototyping bespoke fluidic devices for accommodating nonsupported microelectromembrane extraction (μEME). The analytical performance of 3D-printed μEME devices with distinct cross-sections, including square, circle, and obround, and various channel dimensions was explored against that of commonly used circular polytetrafluoroethylene (PTFE) tubing in flow injection systems. A computer-controlled millifluidic system was harnessed for the (i) automatic liquid-handling of minute volumes of donor, acceptor, and organic phases at the low μL level that spanned from 3 to 44 μL in this work, (ii) formation of three-phase μEME, (iii) in-line extraction, (iv) flow-through optical detection of the acceptor phase, and (v) solvent removal and regeneration of the μEME device and fluidic lines. Using methylene blue (MB) as a model analyte, experimental results evinced that the 3D-printed channels with an obround cross-section (2.5 mm × 2.5 mm) were the most efficient in terms of absolute extraction recovery (59%), as compared to PTFE tubing of 2.5 mm inner diameter (27%). This is attributed to the distinctive convex interface of the organic phase (1-octanol), with a more pronounced laminar pattern, in 3D-printed SL methacrylate-based fluidic channels against that of PTFE tubing on account of the enhanced octanol wettability and lower contact angles for the 3D-printed devices. The devices with obround channels were leveraged for the automatic μEME and in-line clean-up of MB in high matrix textile dyeing wastewater samples with relative recoveries ≥81%, RSD% ≤ 17.1% and LOD of 1.3 μg/mL. The 3D-printed nonsupported μEME device was proven superb for the analyses of wastewater samples with an elevated ionic strength (0.7 mol L −1 NaCl, 5000 mg L −1 Na 2 CO 3 , and 0.013 mol L −1 NaOH) with recorded electric currents below 12 μA. Novelty The coupling of 3D printing with nonsupported μEME in automatic flow-based systems is herein proposed for the first time and demonstrated for the clean-up of troublesome samples, such as wastewaters.

3D printed microfluidic devices for integrated solid-phase extraction and microchip electrophoresis of preterm birth biomarkers

High-performance microchip electrophoresis separations of preterm birth biomarkers using 3D printed microfluidic devices

Automated microfluidic devices integrating solid-phase extraction, fluorescent labeling, and microchip electrophoresis for preterm birth biomarker analysis

Microchip electrophoresis separation of a panel of preterm birth biomarkers

High-Throughput 3D-Printed Model of the Feto-Maternal Interface for the Discovery and Development of Preterm Birth Therapies

A three dimensional thermoplastic microfluidic chip for robust cell capture and high resolution imaging

Making Healthcare Accessible: A Rapid Clean-Room-Free Fabrication Strategy for Microfluidics-Driven Biosensors Based on Coupling Stereolithography and Hot Embossing

3D printed microfluidic devices with integrated versatile and reusable electrodes

Application of a Micro Free-Flow Electrophoresis 3D Printed Lab-on-a-Chip for Micro-Nanoparticles Analysis

Use of 3D printing to integrate microchip electrophoresis with amperometric detection

3D printed enzymatic microchip for multiplexed electrochemical biosensing

3D Printed Microfluidic Device with Integrated Biosensors for Online Analysisof Subcutaneous Human Microdialysate

Integration of 3D printed Mg2+ potentiometric sensors into microfluidic devices for bioanalysis

Microcolumn and Coelution Hydration of Oil Seal Blood Spot for Efficient Screening of Newborn Α-Thalassemia Via Chip Isoelectric Focusing

3D-Printed Modular Microfluidic Device Enabling Preconcentrating Bacteria and Purifying Bacterial DNA in Blood for Improving the Sensitivity of Molecular Diagnostics

3D thermoplastic elastomer microfluidic devices for biological probe immobilization

A 3D printed assisted microfluidic absorbance-based measurement system for Biological Assay

3D printing by two-photon polymerization of hollow microneedles for interstitial fluid extraction

Enhanced Interstitial Fluid Extraction and Rapid Analysis via Vacuum Tube-Integrated Microneedle Array Device

3D-printed stereolithographic fluidic devices for automatic nonsupported microelectromembrane extraction and clean-up of wastewater samples

In Situ Array Microextraction and Metabolic Profiling of Small Extracellular Vesicles to Guide and Monitor Maternal Delivery