Abstract:This study refers to an analysis of the durability of forging tools applied in the second operation of producing a valve forging from the chromium–nickel steel, NC3015. Due to the extreme working conditions of the tools, caused by cyclic thermo-mechanical loads, the average durability of tools made from tool steel WLV (1.2365) equals about 1500 forgings. An in-depth, complex analysis was performed on the technology, using macroscopic tests combined with a measurement of the wear/allowance on the tool working surface through 3D scanning; microstructural tests by means of light microscopy; observations of the changes taking place on the working surface with a scanning electron microscope; microhardness measurements; and multi-variant numerical simulations. It was established that the key issue is the proper selection of the process technological parameters, such as the input material and tool temperature, friction, lubrication, tribological parameters, type of tool material, or punch design, because even small changes made to them significantly affect the service life of forging punches. Therefore, to increase the durability of the forging dies, alternative materials made of W360, as well as two high speed steels, S600 and S705, were applied. However, the implemented punch materials did not bring the assumed effect of increased durability, as the highest average durability of steel W60 equaled only 1500 forgings, whereas in the case of the tool steels, this was below 900 forgings. For this reason, at the further stage, punches with sintered carbide inserts were introduced, which made it possible to significantly improve the durability up to the level of as many as 20,000 forgings, which, at the same time, points to a promising direction of further studies on the use of materials and solutions of this type.

What problem does this paper attempt to address?

The paper primarily discusses the issue of enhancing the durability of punches used for forging valves in closed molds, particularly by using alternative materials to improve their durability during the forging process. In the current production process, the second forging technique is employed, which involves the resistance extrusion of rod material first, followed by the forging of the valve. Although this technique yields products with good mechanical properties, the extremely high unit pressure, high-temperature working environment, and varying tribological conditions result in low durability of the forging tools, especially the punches. The currently used punch material is tool steel WLV (1.2365), with a hardness of 52-53 HRC after heat treatment. During the forging process, the working temperature of the punch is approximately 200°C, and no lubrication or cooling is applied. Due to the high adhesion between the valve material (chromium-nickel steel) and the punch material, and the difficulty in dissolving hard carbides, the punch surface wears out quickly, with an average durability of only 1,500 forgings. To improve this situation, researchers conducted a multifaceted analysis, including macroscopic testing combined with 3D scanning, numerical simulation, microstructure testing, scanning electron microscopy observation, and microhardness measurement. The study found that the correct selection of process parameters is crucial, such as the input material and tool temperature, friction, lubrication, tribological parameters, tool material type, and punch design. Even small changes can significantly affect the tool's lifespan. Therefore, the study attempted to use alternative materials such as W360 and two types of high-speed steels, S600 and S705, but these materials did not significantly improve durability. Ultimately, the introduction of punches with sintered carbide inserts significantly increased durability to 20,000 forgings, pointing to a promising direction for future research. In summary, the paper aims to address the issue of low punch durability in the valve forging process by exploring methods to improve durability through experimental analysis and technical improvements.

Possibilities of Increasing the Durability of Punches Used in the Forging Process in Closed Dies of Valve Forgings by Using Alternative Materials from Tool Steels and Sintered Carbides

Possibilities of Increasing the Durability of Dies Used in the Extrusion Process of Valve Forgings from Chrome-Nickel Steel by Using Alternative Materials from Hot-Work Tool Steels

Structural Features of Fatigue Crack Propagation of a Forging Die Made of Chromium-Molybdenum-Vanadium Tool Steel on Its Durability

Increasing the Working Time of Forging Tools Used in the Industrial Process of Producing a Disk-Type Forging Assigned for a Gearbox through the Application of Hybrid Layers

Durability of Forging Tools Used in the Hot Closed Die Forging Process—A Review

Hard Protective Layers on Forging Dies—Development and Applications

Metallographic Evaluation of Increased Susceptibility to Intermediate Embrittlement of Engine Valve Forgings Made of NCF 3015 High Nickel and Chromium Steel

Possibilities of Measuring and Detecting Defects of Forged Parts in Die Hot-Forging Processes

Optimal design of a multi-ram forging mold for large-diameter valve bodies

Tool Wear Issues in Hot Forging of Steel

Optimizing the Morphology of Primary Carbides and Mechanical Properties during Processing Of Cast-Steel (Din Gx210crv12 1) Press-Forming Dies

Effect of forging sequence and heat treatment on microstructure of high-duty power-plant shaft made of Cr-Mo ultra-high strength steel

Experimental investigations on wear resistance characteristics of different die materials for advanced high-strength steel blanking in close section

An investigation on the suitability of different welding recovery procedures for cold stamping punches in VF800AT steel

Experimental Research and Numerical Modelling of the Cold Forming Process of the Inconel 625 Alloy Sheets Using Flexible Punch

Quantitative Evaluation of Tool Wear in Cold Stamping of Ultra-High-Strength Steel Sheets

Current failure mechanisms and treatment methods of hot forging tools (dies) - a review

Hardness Assessment Considering Nitrided Layers Based on Tempering Tests for Numerical Wear Prediction for Forging Processes

Improvement of the Technology of Precision Forging of Connecting Rod-Type Forgings in a Multiple System, in the Aspect of the Possibilities of Process Robotization by Means of Numerical Modeling

Physical and Numerical Simulations of Closed Die Hot Forging and Heat Treatment of Forged Parts

Experimental and Numerical Studies of Tool Wear Processes in the Nibbling Process