Abstract:Objective: The aim of the study was to determine if laparoscopic skills acquisition will be superior with the use of 3D-enhanced training models with increased dimensionality and spatial complexity compared to standard 3D LapPass training models in novice medical students. We hypothesized that adopting low-fidelity, 3D-enhanced training models in the 2D visual modality may expedite adaptation to monocular cues related to depth perception, enhancing performance. Design: A prospective, single-center, 2-arm, randomized controlled trial with participants randomized equally into either 3D-enhanced or standard 3D group (allocation ratio 1:1, block sizes 2 and 4) performing 2 standardized laparoscopic tasks: (1) polo grasping and manipulation and (2) intracorporeal suturing. Performance was assessed using the Global Operative Assessment of Laparoscopic Skills (GOALS) tool, completion time, and number of errors, with evaluations at baseline, interim, and post-training for each task. A post-study survey measured participant-perceived confidence and performance (ID: NCT06184854). Setting: Barts Cancer Institute, Queen Mary University of London, UK. Participants: Sixty-five medical students, all novices in laparoscopic surgery, were enrolled, with 3 dropouts. Results: Thirty-one participants in each group completed the study with homogeneity regarding demographic data (p > 0.05). Both groups had significantly superior performance post-training compared to baseline in the 2 tasks (intragroup comparison, p < 0.017). In the intergroup comparison, the 3D-enhanced group had statistically significantly greater improvements in the GOALS score parameter and depth perception domain across all comparisons for both tasks (p < 0.05). Time improvement and error reduction also favored the 3D-enhanced group, however, without reaching statistical significance. In the post-study survey, the 3D-enhanced group reported significantly greater perceived post-training confidence and performance in the suturing task alone (p < 0.05). Conclusions: The use of 3D-enhanced training models resulted in superior laparoscopic skills acquisition for novices in 2 tasks compared to standard 3D LapPass models. Therefore, incorporating 3D-enhanced models into laparoscopic training curricula alongside standard 3D LapPass models can supplement learning. Further work should focus on long-term efficacy with a competency-based endpoint.

A deployable curriculum with 3D printed skills trainers for altered airway management

Three-Dimensionally Printed Simulated Tracheas to Improve Cricothyrotomy Skills Among Anesthesia Providers

Use of a 3D printed, color-coded airway model for bronchoscopy training and anatomy learning

Computer-Generated Three-Dimensional Airway Models as a Decision-Support Tool for Preoperative Evaluation and Procedure-Planning in Pediatric Anesthesiology

A three-dimensional (3D) printed paediatric trachea for airway management training

Creating Patient‐Specific 3D‐Printed Airway Models for Slide Tracheoplasty

Three-dimensional Printing As an Aid to Airway Evaluation after Tracheotomy in a Patient with Laryngeal Carcinoma

Using Didactics and Simulation to Enhance Comfort, Knowledge, and Skills of Nonsurgical Trainees Caring for Patients With Tracheostomy and Laryngectomy

Development of a high fidelity subglottic stenosis simulator for laryngotracheal reconstruction rehearsal using 3D printing

Development of an augmented reality system for tracheal intubation guidance of airway management

Difficult airways: a 3D printing study with virtual fibreoptic endoscopy

Multidisciplinary Advanced Surgical Planning for Slide Tracheoplasty Using 3D‐Printed Models

"Just-In-Time" Simulation Training Using 3-D Printed Cardiac Models After Congenital Cardiac Surgery

Development and Evaluation of the Advanced Joint Airway Management System for Educational Utility in Endotracheal Intubation, as Assessed by Expert Paramedic Instructors

Use of a Novel Three-Dimensional Model to Teach Ultrasound-guided Subclavian Vein Cannulation

Three-dimensional printing as a tool in otolaryngology training: a systematic review

Development of a Cost-Effective 3D-Printed Airway Suction Simulator for Respiratory Therapy Students

An interactive and realistic phantom for cricothyroidotomy simulation of a patient with obesity through a reusable design using 3D-printing and Arduino

Design and Validation of a 3D Printed Cranio-Facial Simulator: A Novel Tool for Surgical Education

Validation of a 3D-Printed Silicone-Based Laryngeal Model for Resident Education

Assessing the Efficacy of Enhanced Versus Standard Three-Dimensional Training Models in Laparoscopic Skills Acquisition: A Randomized Controlled Trial of Novice Medical Students