Abstract:Biomass pellets, prepared from wood particles, straws, and other agricultural and forestry residues, possessed the advantages of higher energy density, convenient transportation and storage, and reduced fossil energy consumption and greenhouse gas emissions. They have been widely used in industrial boilers, agricultural greenhouses and household heatingunits. Currently, the efficient measurement and control of pollutant emission during biomass pellet combustion become increasingly important and attract more and more public awareness. Feeding rate is one of the critical factors that determine the combustion status and pollutant emissions. Previous researches mainly focused on the effect of feeding rate on carbon oxide (CO) emission, while the impact on nitrogen oxides (NOx) emission was seldomly reported. The new China National Emission Regulation (NER) issued in early 2012 requires that NOx emission must be controlled below 100 mg/m3. The objective of this study was to investigate the effect of feeding rate on the emission and variation of CO and NOx based on a 5G-20/85-0.23 biomass pellet burner platform. Average feeding rates of 6.9, 6.2, 5.5, 5.0 and 4.5 kg/h were employed, corresponding to the set of working and pausing time in the feeding mechanism at 2 s/13 s, 2 s/15 s, 2 s/17 s, 2 s/19 s, and 2 s/21 s, respectively (labelled as 2/13,2/15,2/17,2/19,2/21). Results showed that CO emission was reduced with the feeding rate decreased from 6.9 to 5.0 kg/h, and the lowest COconcentration of 66 mg/Nm3 was achieved at the feeding rate of 5.0 kg/h. When the feeding rate was further reduced to 4.5 kg/h, the highest CO concentration of 205 mg/Nm3 was obtained. Overall, the CO emission first decreased and then increased for the feeding rate range of 6.9 to 4.5 kg/h. With the decreasing of feeding rate, oxygen (O2) concentration increased first and then decreased. Maximal O2 concentration of 16% was achieved with the feeding mechanism of 2/19. Fluctuation of CO concentration with time reflects the combustion quality and consistency inside the furnace, and minimal fluctuation is preferred. The highest fluctuation of CO concentration appeared when the feeding mechanism was set at 2/13, and a fluctuation peak was noticed at 80 s, which was probably caused by the pellet accumulation in the furnace and incomplete combustion in generating more CO. Overall, the fluctuation period was in good agreement with the feeding period. The effect of feeding rate on NO, NO2, and NOx concentrations was similar to that of CO, with the lowest NOx of 8.8 mg/Nm3 obtained at feeding rate of 5.0 kg/h and highest NOx of 78 mg/Nm3 obtained at 6.9 kg/h. The furnace temperature at lower position reached 758 ℃ at the optimal feeding rate. When the feeding rate was 4.5 kg/h, the temperature was only 375 ℃. The periodical fluctuation of NOx is not as obvious as CO. With the feeding mechanisms of 2/19 and 2/17, very minor fluctuations of NOx with time were observed. The NOx fluctuations were relatively larger with 2/15 and 2/13 feeding mechanisms. In summary, the concentrations of CO and NOx in the emission are significantly affected by biomass pellet feeding rate. Minimal CO and NOx emissions are achieved when the feeding mechanism is set at 2/19. Periodical fluctuation of NOx with time is less obvious compared with CO. These results provide both practical data and theoretical basis for the optimization of feeding rate for biomass pellet burners.

Quality range of ENplus A1 certified wood pellets and their combustion behavior in residential pellet stoves and pellet boilers

Effect of Feeding Rate on Pollutant Emission of Biomass Pellet Burner

Reductions in Emissions of Carbonaceous Particulate Matter and Polycyclic Aromatic Hydrocarbons from Combustion of Biomass Pellets in Comparison with Raw Fuel Burning.

Short rotation woody crops and forest biomass sawdust mixture pellet quality

Characteristics of Commercial and Raw Pellets Available on the Italian Market: Study of Organic and Inorganic Fraction and Related Chemometric Approach

Characterization of Fine and Carbonaceous Particles Emissions from Pelletized Biomass-Coal Blends Combustion: Implications on Residential Crop Residue Utilization in China

Characterizing Dynamic Relationships Between Burning Rate and Pollutant Emission Rates in a Forced-Draft Gasifier Stove Consuming Biomass Pellet Fuels.

Efficiencies and Pollutant Emissions from Forced-Draft Biomass-Pellet Semi-Gasifier Stoves: Comparison of International and Chinese Water Boiling Test Protocols

Pollutant Emissions and Oxidative Potentials of Particles from the Indoor Burning of Biomass Pellets

Chemical characterization of pellet stove ashes: Elemental fractionation of ashes results in volatile particles with high concentrations of cadmium and lead

Performance of Cooking Stoves with Biomass Pellet Fuel

A laboratory assessment of how biomass pellets could reduce indoor air pollution, mitigate climate change and benefit health compared to other solid fuels used in Ghana

In-use emissions and usage trend of pellet heating stoves in rural Yangxin, Shandong Province

Emission of Harmful Substances from the Combustion of Wood Pellets in a Low-Temperature Burner with Air Gradation: Research and Analysis of a Technical Problem

The combustion of torrefied biomass in commercial-scale domestic boilers

Experimental study on the combustion characteristics of biomass pellets

Emission of metals from pelletized and uncompressed biomass fuels combustion in rural household stoves in China.

Novel packed-bed CFD model for pellet combustion: Validation and application to a stove

Factors affecting wood, energy grass and straw pellet durability – A review

Emission of Oxygenated Polycyclic Aromatic Hydrocarbons from Biomass Pellet Burning in a Modern Burner for Cooking in China

Energy usage of spruce with waste face masks and spent coffee grounds as fuel in a pellet boiler