Abstract:<p>Geopolymer concrete (GPC) is an innovative and eco‐friendly construction material. In the experimental investigation, examine the effect of ground granulated blast furnace slag (GGBFS) in the GPC by replacing the fly ash in the various ratios in the different mix design. Fly ash/GGBFS as 100/0, 75/25, 50/50, and 25/75 respectively rate by weight percentage taken in the mix design. All the mix designs specimens cured in two types are ambient‐cured and oven‐cured at 80°C for 24 h after the demolding of the samples, and both types samples tests at 7, 14, 28, 42 and 56 days for strength (compressive, splitting tensile, flexural strength) and non‐destructive (rebound strength and ultrasonic pulse velocity [UPV]). Examine the density, Poisson ratio and modulus of elasticity of the all mix designs samples of both types of cured specimens at 28 days after the casting. Geopolymer bonding formation is amorphous or crystalline in the bonding mineral components analyzed by the X‐ray diffraction test. Examine the thermal stability of the geopolymer bond paste after the gaining strength up to the 850°C by increases the temperature 10°C per minute gradually in the thermogravimetric analysis after the 28 days of casting after the experimental investigation results indicate that the ambient‐cured samples got less engineering strength as compared to the oven‐cured samples. However, in both cured samples, the mix has a ratio of 75/25 of fly ash/GGBFS as binding material got higher mechanical strength than other mixes. In the GPC mix design, the GGBFS 25% by weight of binder with fly ash has instantly increased the strength. However, after the increase of replacement of GGBFS with the flyash slightly decreases the strength of the mix designs. The rebound hammer test strength was marginally higher than the same mix designs specimens destructive compressive strength. UPV shows the similar trends of the graph of ambient‐cured and oven cured to the rebound strength. The oven‐cured specimens show a higher UPV compared to the ambient‐cured specimens. The ambient‐cured sample has a higher density compared to the oven‐cured GPC specimens of different mix designs. Still, in both cured samples, mix design samples of 75/25 fly ash/GGBFS ratio got the average maximum density. The Poisson ratio of the ambient‐cured GPC specimens is slightly excessive than oven‐cured specimens. Still, the modulus of elasticity of the GPC mix designs is higher for the oven‐cured samples. Weight loss of the specimens occurs at the elevation of temperature with the rise in the content of GGBFS in the mix gradually up to the 850°C, but in oven‐cured samples, the weight loss was slightly excessive compared to the ambient‐cured samples. After the experimental results of mechanical properties, propose the relationship equations among the mechanical properties. Relationship between flexural strength and compressive strength, splitting tensile and compressive strength, and modulus of elasticity compressive strength. <span>Proposed equations</span> are , respectively.</p>

Ultrasonic Pulse Velocity and Mechanical and Physical Properties of Structural Geopolymer Concrete Containing Lightweight Expanded Clay Aggregates: Experimental and Computational Study

Geopolymer Concrete with Lightweight Fine Aggregate: Material Performance and Structural Application

Optimization of mechanical properties and pore structure of lightweight geopolymer concrete using GGBFS based on LF-NMR technology

Compressive Strength and Chloride Resistance of Slag/Metakaolin-Based Ultra-High-Performance Geopolymer Concrete.

Effect of ground granulated blast furnace slag and fly ash ratio and the curing conditions on the mechanical properties of geopolymer concrete

Mechanical properties of basalt fiber reinforced ambient-cured lightweight expanded polystyrene geopolymer concrete

Synthesis of Sustainable OPC‐Blended Geopolymer Concrete: Experimental and Modeling Study

Experimenting the influence of corncob ash on the mechanical strength of slag-based geopolymer concrete

Effect of GGBS Content and Water/Geopolymer Solid Ratio on the Mechanical, Elevated Temperature Resistance, and Sorptivity Properties of FA/GGBS-Based Geopolymer Concrete

Sustainable Utilization of Waste Pumice Powder in Slag-Based Geopolymer Concretes: Fresh and Mechanical Properties

Influence of polypropylene and steel fibers on the mechanical properties of ultra-high-performance fiber-reinforced geopolymer concrete

Hybrid effect of carbon nanotubes and basalt fibers on mechanical, durability, and microstructure properties of lightweight geopolymer concretes

Development of Sustainable Slag-based Geopolymer Concrete Using Different Types of Chemical Admixtures

Influence of microsilica and polypropylene fibers on the fresh and mechanical properties of ultra-high performance geopolymer concrete (UHP-GPC)

Mechanical and durability analysis of geopolymer concrete incorporating bauxite residue, phosphogypsum, and ground granulated blast slag

Properties and Durability Performance of Lightweight Fly Ash Based Geopolymer Composites Incorporating Expanded Polystyrene and Expanded Perlite

Geopolymer Concrete with Lightweight Artificial Aggregates

Compressive Strength and Thermal Conductivity of Fly Ash Geopolymer Concrete Incorporated with Lightweight Aggregate, Expanded Clay Aggregate and Foaming Agent

The Effects of Additives to Lightweight Aggregate on the Mechanical Properties of Structural Lightweight Aggregate Concrete

Durability, Microstructure, and Optimization of High-Strength Geopolymer Concrete Incorporating Construction and Demolition Waste

Experimental study on the properties of ultra-high-strength geopolymer concrete with polypropylene fibers and nano-silica