Abstract:In this study, a novel design of porous microchannel heat sink (MCHS) with graded porosity configuration is proposed in the hope of attaining lower flow and thermal resistances than constant porosity (CP) configuration. The efficacy of new scheme is validated by utilizing a three-dimensional solid-fluid conjugate model based on the finite volume method, which considers the flow and heat transfer of microencapsulated phase change material slurry (MPCMS) inside the porous fins. It is reported that the thermal performance of porous MCHS with constant and graded porosity configurations is significantly better than that of non-porous MCHS. The feasibility of new design is verified by comparing the hydrothermal behavior of multiple graded porosity MCHSs and CP configuration for different fin designs (involving the number of graded equidistant fins N , graded length ratio R , and fin-to-pitch width ratio β ) and operating conditions (including Reynolds number Re , mass fraction c m , and inlet velocity u in ). The comprehensive performance improvement mechanism of MPCMS in graded porosity microchannels is discussed through the analysis of flow and thermal details, field synergy angle ( θ ) and field synergy number ( Fc ), and the overall performance of new design is evaluated by performance evaluation factor ( PEF ). Results indicate that the six types of porous MCHS with stepwise varying porosity exhibit lower thermal resistance than CP mode, and better thermal behavior and larger PEF can be obtained at N = 2 and β = 0.7. Smaller and larger R should be chosen for stepwise increasing porosity (SIP) and stepwise decreasing porosity (SDP) modes, respectively, to achieve higher heat transfer enhancement while avoiding greater friction losses. The Fc value of porous MCHS with various porosity configurations is about two orders of magnitude less than 1 and shows a monotonically reducing trend with Re , and the synergistic effect deteriorates at high Re . Compared to the CP mode, a low- θ "drift" toward the low porosity region of porous fin occurs within the graded porosity MCHS, which decreases and increases in the downstream and upstream directions of the "drift", respectively. Among the novel MCHS designs, the z -directional SIP mode acquires the best overall performance due to the excellent synergy between the velocity and temperature fields, and its PEF consistently exceeds 1.13 and reaches up to 1.33. Generally speaking, the fin porosity of graded porosity MCHS near the channel cavity, channel top, and channel inlet should be greater for superior comprehensive performance.

Dynamic characteristics of a shell and plate particle‐SCO 2 moving packed bed heat exchanger with various SCO 2 channel configurations

Comparative study on the thermal-hydraulic performance of a shell and plate particle-SCO2 moving packed bed heat exchanger with various channel configurations

Comparative study on the thermal-hydraulic performance of a shell and plate particle-SCO<sub>2</sub> moving packed bed heat exchanger with various channel configurations

Thermal Design of Large Plate-Fin Heat Exchanger for Cryogenic Air Separation Unit Based on Multiple Dynamic Equilibriums

Numerical Study on Hydrodynamics, Mixing and Heat Transfer of Highly Viscous Fluid in a Novel Shell-and-tube Heat Exchanger with X-type Baffles

Segmented Design of Performance Enhancement for Large Plate Fin Heat Exchanger of Cryogenic Air Separation Unit

Heat transfer model of a particle energy storage‐based moving packed bed heat exchanger

Dynamic Behaviors and Nonlinear Wave Model Control of Heat Integrated Air Separation Columns with Different Purities

Numerical Study on Thermal Performance of a BOG Heat Exchanger in the Inclined Condition

Effect of Inlet Flow Maldistribution on the Passage Arrangement Design of Multi-Stream Plate-Fin Heat Exchanger

Field Synergy Analysis of the Dynamic Process of a Multi-stream Heat Exchanger

Dynamic regulation of the thermal performance of the S–CO 2 minichannel using a piezoelectric oscillating fin

Performance of printed circuit heat exchangers in SCO2 Brayton/Organic Rankine combined cycle: Assessment of simplified boiling temperature and heat flux type of boundary conditions

Analysis on the flow and heat transfer performance of SCO 2 in airfoil channels with different structural parameters

Investigation of the thermal-hydraulic characteristics of SCO 2 in a modified hybrid airfoil channel

Numerical simulation of heat transfer performance of spiral wound heat exchanger under sloshing condition

Analysis on flow and heat transfer performance of SCO2 in airfoil channels with different fin angles of attack

Thermal Compensation Effect of Passage Arrangement Design for Inlet Flow Maldistribution in Multiple-Stream Plate-Fin Heat Exchanger

Optimization and Invasive Monitoring for the Local Flow Velocity Maldistribution in Plate-Fin Heat Exchangers

Field synergy analysis on thermal-hydraulic behavior of phase change slurry in porous microchannel heat sink with graded porosity configuration

Analysis of stream flow and its impact on thermal performance in shell-side of heat exchangers based on flow dead zone