Abstract:Current research is focused on developing active materials through surface functionalization, porosity, composites, and doping for ultrafast electric double layer capacitors (EDLCs). In this study, deviating from existing strategies focused on active materials, we designed tunable 3D microgrid-patterned (MP) surface morphologies on Ni foams used as current collectors using SUS meshes as rigid stamps during roll pressing. The surface geometries of the MP-Ni foams were controlled to standard mesh scales of 24, 40, and 60 (denoted as 24MP-Ni, 40MP-Ni, and 60MP-Ni, respectively). The three MP-Ni samples with different microgrid sizes presented different surface geometries, such as root-mean-square roughness (Rrms), skewness roughness (Rsk), and width/depth scales of the microgrid patterns. Consequently, 40MP-Ni demonstrated an optimized surface geometry with high Rrms (35.4 μm) and Rsk (−0.19) values, which facilitated deep slurry infiltration and increased its contact area with the active material. Surface optimization of the MP-Ni enabled ultrafast and reversible charge transport kinetics owing to its relaxed electron transfer resistance and robust adhesion to the active material compared with bare Ni foam. EDLC electrodes with 40MP-Ni achieved an ultrafast-rate capability (96.0 F/g at 20 A/g) and ultrafast longevity (101.9% capacity retention after 5000 cycles at 5 A/g) without specific modification of active material.
What problem does this paper attempt to address?
### What problem does this paper attempt to solve?
This paper aims to solve the problem of ultra - fast charge - discharge performance in electrochemical double - layer capacitors (EDLCs). Specifically, the researchers try to improve the ultra - fast charge - discharge ability and cycle stability of EDLC electrodes by optimizing the surface geometric structure of the current collector, without relying on special modification of the active material.
#### Main problems and solutions:
1. **Limitations of traditional strategies**:
- Existing research mainly focuses on developing high - performance active materials, such as improving the performance of EDLCs through means like surface functionalization, increasing porosity, composite materials, and doping.
- Although these methods are effective, they often overlook the important role of the current collector in the electrode - electrolyte interface.
2. **Proposed new strategy**:
- This research introduces a novel method, that is, using microgrid - patterned (MP) nickel foam as the current collector, and using standard sieves (SUS mesh) of different specifications as rigid stamps to produce nickel foam with a controllable 3D microstructure during the rolling process.
- By changing the specifications of the sieve (24 - mesh, 40 - mesh, 60 - mesh), the microstructure characteristics on the surface of the nickel foam, such as width, depth, and roughness parameters (root - mean - square roughness \( R_{\text{rms}} \) and skewness roughness \( R_{\text{sk}} \)), can be systematically regulated.
3. **Optimization effects**:
- The experimental results show that the 40MP - Ni sample exhibits the best surface geometric structure, with a relatively high root - mean - square roughness (\( R_{\text{rms}} = 35.4 \, \mu m \)) and a slightly negative - skewed skewness roughness (\( R_{\text{sk}} = - 0.19 \)), which helps the deep penetration of the slurry and increases the contact area with the active material.
- The results indicate that the optimized MP - Ni current collector significantly improves the electron transfer kinetics, reduces the electron transfer resistance, and enhances the adhesion to the active material, thereby achieving ultra - fast and reversible charge - discharge performance.
4. **Specific performance improvement**:
- The EDLC electrode using 40MP - Ni as the current collector exhibits an excellent specific capacitance (96.0 F/g) at a high current density of 20 A/g, and still maintains a capacity retention rate of 101.9% after 5,000 cycles.
- These results prove that by optimizing the surface geometric structure of the current collector, the ultra - fast charge - discharge performance and long - life characteristics of EDLC electrodes can be significantly improved without changing the active material.
In conclusion, this paper solves the performance bottleneck problem of existing EDLC electrodes in the ultra - fast charge - discharge process through the innovative microgrid - patterned nickel foam design, providing new ideas for the design of future high - performance energy storage devices.