Abstract:In the southern China , the sugarcane is mostly planted on the slopes and hilly areas . Because of the influence caused by the typhoons and monsoons , the sugarcane always render in the state of lodging and bending . Lifting up the sugarcane is the first step of the mechanized harvesting of sugarcane . It is demanded that the harvest mechanic of sugarcane should be adapt to the planting patterns and growth condition , in order to lift up the sugarcane in different lodging status . Currently , the design and the research method on sugarcane lifter was traditional , which usually did static analysis only and did not take the dynamic characteristics into consideration . The propped effect of the existing mechanism is poor and the efficiency is not really high , meanwhile , the sugarcane lifter has problems caused by the unreasonable structure design and operation parameters . In order to solve these problems , the virtual prototype technology will be used to do the virtual experiment on sugarcane lifter .At the same time , the technology will also analyze its key technology , save the cost of physical prototype research and development , and shorten the development cycle of the physical prototype as well . The investigated subject of this paper was mainly the sugarcane lifter with the 60° installation angle and the equivalent pitch spiral . Aimed at the problems of the sugarcane lifting caused by the unreasonable structure design and the operation parameters , the three-dimensional model would be imported into the ADAMS software to do the dynamic simulation . The method of three levels and three factors comprehensive test was used , whose impact factors were sugarcane lifter speed , pitch and the forward speed . Regarding the lifting height as the evaluation index , it intended to find the optimum combination for the virtual experiment of the sugarcane lifter structure and the working parameters , meanwhile , the test data variance would be analyzed by the MATLAB software . Through the analysis of the dynamic simulation of the sugarcane lifter , it was clear that when the time was 0 to 1.5 s , the sugarcane lifter would not get in touch with the sugarcane , and as a result , the centroid vertical displacement was not changed accordingly ;but when the time was 1.5 to 4.5 s , the sugarcane would be lifted by the sugarcane lifter , and the centroid vertical displacement was correspondingly increased gradually . When the time was more than 4.5 s , the fluctuations of the centroid vertical displacement would come out because of the non-existence of the simulation of cutting part.In the combination of the ADAMS virtual comprehensive test , the best operating and structure parameters for the angle of 60° installation sugarcane lifter was that :when the speed of the sugarcane lifter was up to 120 r/min , the pitch of thread was 360 mm , and the forward speed was 350 mm/s , the lifting height of the 60° side lodging sugarcane would reach the maximum 186.9 mm . In addition , the three factors have mutual interactions with each other , and this moment was the strongest time that the forward speed affected the height of the sugarcane lifter , all of which will eventually provide the theory basis for the improvement of sugarcane lifter .

Discrete Meta-Simulation of Silage Based on RSM and GA-BP-GA Optimization Parameter Calibration

Calibration and Validation of Simulation Parameters for Maize Straw Based on Discrete Element Method and Genetic Algorithm-Backpropagation

An Investigation on a Comprehensive Calibration Technique to Determine the Discrete Elemental Characteristics of Unrotted Sheep Dung at Varying Water Concentrations

A Calibration of the Contact Parameters of a Sesbania Seed Discrete Element Model Based on RSM

Discrete Element Simulation Modeling Method and Parameters Calibration of Sugarcane Leaves

Parameter optimization of the spiral fertiliser discharger for mango orchards based on the discrete element method and genetic algorithm

PARAMETER CALIBRATION OF DISCRETE ELEMENT SIMULATION MODEL OF WHEAT STRAW-SOIL MIXTURE IN HUANG HUAI HAI PRODUCTION AREA

Parameter Calibration for Discrete Element Simulation of the Interaction between Loose Soil and Thrown Components after Ginseng Land Tillage

Friction coefficient calibration of corn stalk particle mixtures using Plackett-Burman design and response surface methodology

Calibration and test of contact parameters for alfalfa stalk at primary florescence based on discrete element method

Parameter calibration for simulation of Gentiana seedling substrate based on discrete element method

DEM Parameter Calibration of Maize Seeds and the Effect of Rolling Friction

Parameter calibration of discrete element simulation for the interaction between heavy soil and soil-engaging components in shellfish culture

Optimization of parameters for sugarcane lifter based on simulation of virtual prototype

Parameter Calibration of Pig Manure with Discrete Element Method Based on JKR Contact Model

Numerical simulation of Fertilizer Shunt-Plate with uniformity based on EDEM software

ESTABLISHMENT AND CALIBRATION OF DISCRETE ELEMENT MODEL OF KING GRASS STALK BASED ON THROWING TEST

Novel Intelligent System Based on Automated Machine Learning for Multiobjective Prediction and Early Warning Guidance of Biogas Performance in Industrial-Scale Garage Dry Fermentation

Establishment and Verification of a Model for the Movement of Pulverized Sweet Sorghum Stalks in a Rotary Drum Bioreactor by Discrete Element Method

Calibration of discrete meta-parameters of bamboo flour based on magnitude analysis and BP neural network

Modeling and Optimization of the Hydrolysis and Acidification Via Liquid Fraction of Digestate from Corn Straw by Response Surface Methodology and Artificial Neural Network