Artificial Muscles: Selected papers from the 5th World Congress on Biomimetics, Artificial Muscles and Nano-Bio (Osaka, Japan, 25–27 November 2009)
Mohsen Shahinpoor
DOI: https://doi.org/10.1088/0964-1726/20/12/120201
IF: 4.1
2011-11-22
Smart Materials and Structures
Abstract:The 5th World Congress on Biomimetics, Artificial Muscles and Nano-Bio and the 4th International Conference on Artificial Muscles were held in Osaka, Japan, 23–27 November 2009. This special section of Smart Materials and Structures is devoted to a selected number of research papers presented at this international conference and congress. Of the 76 or so papers presented at the conference, only 10 papers were finally selected, reviewed and accepted for this special section, following the regular reviewing procedures of the journal. This special section is focused on polymeric artificial muscles, electroactive polymers, multifunctional nanocomposites and their applications. In particular, an electromechanical model for self-sensing ionic polymer–metal composite actuating devices with patterned surface electrodes is presented which discusses the concept of creating self-sensing ionic polymer–metal composite (IPMC) actuating devices with patterned surface electrodes where actuator and sensor elements are separated by a grounded shielding electrode. Eventually, an electromechanical model of the device is also proposed and validated. Following that, there is broad coverage of polytetrahydrofurane–polyethylene oxide–PEDOT conducting interpenetrating polymer networks (IPNs) for high speed actuators. The conducting polymer (poly(3,4-ethylenedioxythiophene)) is incorporated within the IPNs, which are synthesized from polyethylene oxide (PEO)/polytetrahydrofurane (PTHF) networks. PEO/PTHF IPNs are prepared using poly(ethylene glycol) methacrylate and dimethacrylate and hydroxythelechelic PTHF as starting materials. The conducting IPN actuators are prepared by oxidative polymerization of 3,4-ethylenedioxithiophene (EDOT) using FeCl3 as an oxidizing agent within the PEO/PTHF IPN host matrix. Subsequently, giant and reversible magnetorheology of carrageenan/iron oxide magnetic gels are discussed and the effect of magnetic fields on the viscoelastic properties, magnetorheological effect of carrageenan gel containing iron oxide particles are investigated using dynamic viscoelastic measurements under magnetic fields. Furthermore, the relationship between the magnetorheology and the elasticity of magnetic gel is discussed. This special section then covers the characteristics of ionic polymer–metal composite with chemically-doped TiO2 particles to improve the bending performance of ionic polymer–metal composite (IPMC) actuators. This study is mainly focused on the characterization of the physical, electrochemical, and electromechanical properties of TiO2-doped ionic polymer membranes, and IPMCs prepared by the sol–gel method, which results in a uniform distribution of the particles inside the polymer membrane. It was determined that the lifetime of IPMC is strongly dependent on the level of water uptake. This paper is then followed by a presentation on training and shape retention in conducting polymer artificial muscles. Electrochemomechanical deformation (ECMD) of the conducting polymer, polyaniline film, is studied to investigate the behavior of actuation under tensile loads. The ECMD is induced by strains due to insertion of ionic species (cyclic strain) and a creep due to applied loads during the redox cycle. The cyclic strain is enhanced by the experience of high tensile loads, indicating a training effect. The training effect is explained by the enhanced electrochemical activity of the film. The special section then presents a paper on the current status and future prospects of power generators using dielectric elastomers. Electroactive polymer artificial muscle (EPAM), known as 'dielectric elastomer', appears to offer unique capabilities as an actuator and electrical power generator. However, the power output levels of such generators are small and the efficiencies are rather high. For example, electrical energy conversion efficiency of over 70% has been achieved. The ability of EPAM to produce hydrogen fuel for energy storage was also demonstrated. Because the energy conversion principle of EPAM is capacitive in nature, the performance is largely size-independent. Formation of motile assembly of microtubules driven by kinesins is presented next. Microtubule (MT) and kinesin are rail and motor proteins that are involved in various moving events of eukaryotic cells in natural systems. In vitro, the sliding motion of microtubules (rail) can be reproduced on a kinesin (motor protein)-coated surface coupled with adenosine triphosphate (ATP) hydrolysis, which is called a 'motility assay'. Based on this technique, a method is reported for forming MT assemblies by an active self-assembly (AcSA) process, in which MTs are crosslinked during a sliding motion on a kinesin-coated surface. Streptavidin (ST) is employed as glue to crosslink biotin-labeled MTs. This discussion is then followed by a paper on the performances of fast-moving low-voltage electromechanical actuators based on single-walled carbon nanotubes and ionic liquids. Here the mechanical and electrical properties of the polymer-free single-walled carbon nanotube (SWNT) sheets containing different contents of ionic liquids (ILs) are reported. The polymer-free SWNT sheets are prepared with the knowledge that millimeter-long 'super growth' carbon nanotubes (SG-SWNTs), produced by a water-assisted modified CVD method, associate together tightly with ILs. The molecular mechanism of electroactive polymer actuators is then discussed in the next paper. Movement of ionic electroactive polymer actuators utilizes their anisotropic volume change, which is induced by the applied voltage. The mechanism of the volume change is, however, not well understood, especially at the molecular level. The current understanding of the mechanism of the volume change at the molecular level is reviewed, focusing on the actuators made with carbon materials. Then, the pressure generated in the actuators in response to the applied voltage based on the results of the Monte Carlo simulation is discussed. It is shown that the mechanism of the actuators can be analyzed at the molecular level in terms of the balance between the electrostatic and volume exclusion interactions that act among the electrode materials and the electrolyte ions. The special section then presents a master curve for analyzing the electrochemical aging and memory effects of poly(3,4-ethylenedioxythiophene). The memory effect of conducting polymers in an electrochemical environment is investigated. This memory effect is related to the electromechanical responses of the conducting polymer. Poly(3,4-ethylenedioxythiophene) is chosen because of its interesting properties—mainly its chemical and electrochemical stabilities. By means of cyclic voltammetry, the influence of the waiting time tw at a holding potential Ew in relation to the conformational relaxation process occurring in the conducting polymer is analyzed. The effect of electrochemical aging on the electrical properties is also explained from the viewpoint of the rearrangement of polymer chains. This completes a brief report on the content of the special section on artificial muscles. I would like to thank the contributing authors of this collection of papers on artificial muscles for their outstanding and unique contributions. I am also indebted to all of the reviewers, editors and editorial staff who handled the reviews of all the papers for their time and effort. I would like to express my sincere thanks and appreciation to Professor E Garcia, Editor-in-Chief, for his encouragement and support, and for providing the opportunity to publish this special section of Smart Materials and Structures. I am also grateful to the IOP Publishing team for their support. In particular, I am greatly indebted to publisher Natasha Leeper, for her help and excellent management in the preparation of this special section on artificial muscles.
materials science, multidisciplinary,instruments & instrumentation