Abstract:Each year in the United States, approximately 242 million automobile, truck and specialty tires are discarded. Almost 78% of these scrap tires wind up in overcrowded landfills, and thousands more are strewn across the country's empty lots, highways and illegal tire dumps. Used tires pose both a serious public health and an environmental threat. Therefore, economically feasible alternatives for scrap tire disposal must be found. Some of the current uses of scrap tires are tire-derived fuel, barrier reefs, and crumb rubber as an asphalt additive. However, all of the recycling, re-use and recovery practices combined only consume about 22% of the discarded tires. Thus, a need still exists for the development of additional uses for scrap tires. This paper addresses one potential use of scrap tires within the civil engineering field. Specifically, the feasibility of using shredded tires as a lightweight backfill material for retaining walls has been investigated. In this study, laboratory tests were first performed to determine the engineering properties of shredded tires. Based on sieve analyses, the shredded tires used for this study can be classified as uniformly graded material. The unit weight of shredded tires was found to range from 35 to 38 lbs ft−3(pcf), and the hydraulic conductivity was determined to be 0.03 cm s−1. The values of shear strength parameters, cohesion and angle of internal friction, were determined to be 147 lbs ft−2(psf) and 27 degrees, respectively. Using these properties, retaining walls of various heights were then designed using shredded tires as the backfill material. Retaining walls were also designed using conventional sand as the backfill material for comparison purposes. When comparing the overall cost for the retaining wall using shredded tires with the retaining wall using sand, a substantial cost saving was realised by the use of shredded tires. An increase in the factor of safety was also a result of using shredded tires instead of sand as backfill. The results of this study indicate that shredded tires have a definite potential to be used as a backfill material for retaining structures.

Tire Shreds as Lightweight Retaining Wall Backfill: Active Conditions

Tire-reinforced earthfill. Part 1: Construction of a test fill, performance, and retaining wall design

USE OF SHREDDED TIRES AS LIGHTWEIGHT BACKFILL MATERIAL FOR RETAINING STRUCTURES

Active earth pressures against rigid retaining walls with narrow cohesive backfill

Analysis Of Active Earth Pressure On Rigid Retaining Walls Considering Soil Arching

Feasibility Study of Retaining Walls Backfilled with Sand-Tire Chip Mixtures

Numerical Analysis of Consolidation Behavior of Soil-Bentonite Backfill in a Full-Scale Slurry Trench Cutoff Wall Test

Life cycle assessment of retaining wall backfilled with shredded tires

Experimental evaluation of mechanically stabilized earth walls with recycled crumb rubbers

Active earth pressure of narrow cohesive backfill on rigid retaining wall of rotation about the bottom

Load-Deformation Behavior of Geosynthetic-Reinforced Retaining Walls with Limited Fill Space Under Static Footing Loading

Bearing capacity of circular footings on multi-layered sand-waste tire shreds reinforced with geogrids

Calculation of earth pressure against rigid retaining wall rotating outward about base

Response of shallow foundations in tire derived aggregate

Shaking Table Tests on the Seismic Performance of a Flexible Wall Retaining EPS Composite Soil

Seismic response comparison of various geogrid reinforced earth-retaining walls: based on shaking table and 3D FE analysis

Active Earth Pressure of Narrow Backfill on Inverted T-Type Retaining Walls under Translation Mode

Experimental and Theoretical Investigations on Active Earth Pressure Distributions behind Rigid Retaining Walls with Narrow Backfill under a Translational Mode

Experimental Investigations on the Pull-Out Behavior of Tire Strips Reinforced Sands

Semianalytical Solution for Earth Pressure of Narrow Granular Backfill with a Log-Spiral Failure Surface behind Retaining Walls under Translational Mode

Earth Pressure Against Rigid Retaining Wall Rotating about Top