Abstract:The motivation behind present investigation has been a step to create preliminary understanding towards structure‐property correlation i. e., microstructure and microhardness in presence of boron in P91 steel and in its subzones of heat‐affected zone with Gleeble simulation. For microstructure characterization and its comparison amongst selected two steels, light microscopy for prior austenite grain size, morphology of prior austenite grain boundaries and scanning electron microscopy at low‐resolution and high‐resolution in order to study evolution of sub‐structure i. e. martensitic lath block structure and nano‐precipitates were employed. Electron backscatter diffraction measurements of all coupons were done to understand the distribution and contribution of relative fraction of various grain and sub‐grain boundaries within local microstructure. Main effects of addition of 100 ppm boron to standard P91 steel as observed from present microstructural evaluation are; existence of fine nano‐precipitates P91‐coarse grained heat affected zone than its P91B counterpart, grain refinement in fine‐grained heat‐affected zone of both steels with partial dissolution of nano‐precipitates, coarsened nano‐precipitates in P91‐fine‐grained heat‐affected zone after post weld heat treatment, mixed‐structure of partially transformed martensite and coarsened undissolved prior austenite grains with nano‐precipitates in P91‐inter‐critical heat‐affected zone than P91B‐inter‐critical heat‐affected zone. However, difference in microhardness was primarily owing to variation of nano‐precipitates fraction area. In addition, present work induced grounds for microstructure stability i. e., grain boundary hardening in P91B weldments that suppresses type IV failure. Gleeble simulation of P91 and P91B steels was carried out to obtain various heat‐affected zones i. e., coarse‐grained, fine‐grained, and inter‐critical heat‐affected zone. The novel achievement of this work is development of reasoning on stability of microstructure in P91B weldments from electron backscatter diffraction analysis for improved grain boundary hardening that leads to suppression of type IV failure.

Study of distribution of B and N using auger electron spectroscopy (AES) and atom probe tomography (APT) techniques, in modified 9Cr 1Mo steels with controlled addition of these elements

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

The Determination of Degree of Order of Nearby Grain Boundary in the Ni3A1 Family

Preferential distribution behavior of B and its enhancement on creep strength of alumina-forming austenitic heat-resistant steel

Influences of Partial Substitution of C by N on the Microstructure and Mechanical Properties of 9cr18mo Martensitic Stainless Steel

Microstructural Analysis on Grain Boundary of Boron– and Zirconium–Containing Wrought Nickel-Based Superalloys

Microstructure and Crystallography of Borides and Secondary Precipitation in 18 Wt.% Cr–4 Wt.% Ni–1 Wt.% Mo–3.5 Wt.% B–0.27 Wt.% C Steel

The Effect of Boron Addition on the corrosion behavior of Ni Cr Modental alloy prepared by powder metallurgy.

Improved creep resistance of 20Cr25NiNb heat resistant steels through grain boundary intermetallic precipitation strengthening

Boron addition to AISI A213/P91 steel: Preliminary investigation on microstructural evolution and microhardness at simulated heat‐affected zone

Formation and Kinds of Boride on Microstructure Evolution and Mechanical Properties in Ti47.5Al2.0Cr2.0NbxB Alloys

Precipitation Behavior of Fe2Nb Laves Phase on Grain Boundaries in Austenitic Heat Resistant Steels

A new strategy for developing a Nb microalloyed fire-resistant steel: effects of boron and cooling rate

Effect of Boron on Hot Ductility and Room-Temperature Tensile Properties of Microalloyed Steels with Titanium and Niobium

Effect of Boron on Microstructures and Low-Temperature Impact Toughness of Medium-Carbon CrMo Alloy Steels with Different Quenching Temperatures

On the effect of boron on grain boundary character in a new polycrystalline superalloy

Effect of boron concentration on microstructures and properties of Fe–B–C alloy steel

Strengthening Of An Al-Containing Austenitic Stainless Steel At High Temperature

Microstructure and Crystallography of Borides and Mechanical Properties of Fe–B–C–Cr–Al Alloys

The Effect of Boron on the Microstructure and Properties of Refractory Metal Intermetallic Composites (RM(Nb)ICs) Based on Nb-24Ti-xSi (x = 16, 17 or 18 at.%) with Additions of Al, Cr or Mo

Effect of Trace Element B on the Microstructure and Mechanical Properties of 8Cr4Mo4V Bearing Steel