Abstract:The overall performance of the composite insulation external walls (CIEW) may not be optimal as the current methods calculate the optimal insulation thickness (OIT) considering only the cost due to an increase in the insulation layer. The influence of base wall costs on optimum construction form is worthy of further investigated. This study is to close the knowledge gap to improve the overall performance of a CIEW. For this, an optimization model was established using a life-cycle cost analysis (LCCA) method considering the structural and insulation layers to determinate the optimal structural layer thickness (OSLT), optimal insulation thickness (OIT), and overall U-value of a CIEW. A case study of a masonry wall in a cold area in Beijing was conducted. Coal-fired boiler (CFB), gas-fired boiler (GFB), and air source heat pump (ASHP) were used as heat sources, and extruded polystyrene panel (XPS), rock wool (RW), and glass wool (GW) were used as insulation materials. The OSLT, OIT, optimal overall U-value, life-cycle cost (LCC), life-cycle saving (LCS) and payback period were calculated and compared between scenarios determined by this model and traditional model when the structural layer was known. The results indicate that the scenario determined by this model could achieve better energy-saving benefits. The payback period ranged from 2.25 to 5.07 years. The LCC saving rates and the growth ratio of life-cycle savings varied with these materials and heat sources from 0.55% to 3.70% and 0.19% to 1.40%, respectively. When same heat source being used, the total thicknesses of the structure and insulation layer (TTSIL) equals 300 mm, the order of achieved energy-saving benefits is XPS>GW>RW. The optimal overall U-value of the CIEW was independent of the required thickness of the structural and insulation layers and decreases with increasing unit heat consumption of heat sources. However, the energy efficiency revenue decreases with an increase in the TTSIL. The proposed method provides different proportions of thicknesses for construction walls and insulation layers, the variation of heat accumulation potential, influence on peak cooling/heating demand and environmental impact of the optimal CIEW will be studied in the future.

A low-carbon optimization design method for building roof insulation using comprehensive economic analysis model and evaluation index

Multi-objective Optimization of the Office Park Building Envelope with the Goal of Nearly Zero Energy Consumption

Economic Analysis of Energy-Saving Renovation Measures for Urban Existing Residential Buildings in China Based on Thermal Simulation and Site Investigation

Multi-objective optimization of building design for life cycle cost and CO2 emissions: A case study of a low-energy residential building in a severe cold climate

Multi-objective Optimization Design of Low-carbon Modular Building

The Method of Reducing Heat Loss from Thermal Bridges in Residential Buildings with Internal Insulation in the Hot Summer and Cold Winter Zone of China

Optimal Analysis of Multi-Energy System Towards Low-Carbon Building

CALCULATIONS OF ECONOMIC THERMAL INSULATION THICKNESSES ON ROOF AND WALLS OF AIR-CONDITIONED BUILDINGS

Optimization strategies of the envelope insulation for a detached house based on load sensitivity and thermal storage performance

Optimum construction form and overall U-value of composite insulation external wall

Optimization Strategies for the Envelope of Student Dormitories in Hot Summer and Cold Winter Regions: Multi-Criteria Assessment Method

Research and Exploration of Green Building Based on the Basic Theory of Urban Development

Sensitivity Analysis for Carbon Emissions of Prefabricated Residential Buildings with Window Design Elements

Multi-Objective Optimization of Ultra-Low Energy Consumption Buildings in Severely Cold Regions Considering Life Cycle Performance

Multiobjective Optimization Design of Green Building Energy Consumption Based on Inorganic Thermal Insulation Nanomaterials

Low-carbon design optimization of reinforced concrete building structures using genetic algorithm

Optimization of integrated energy system for low-carbon community considering the feasibility and application limitation

A three-stage decision-making process for cost-effective passive solutions in office buildings in the hot summer and cold winter zone in China

Energy Efficiency Model Construction of Building Carbon Neutrality Design

Grasshopper platform-assisted design optimization of fujian rural earthen buildings considering low-carbon emissions reduction

Energy-saving retrofits of prefabricated house roof in severe cold area