Abstract:To reduce carbon emissions associated with substantial concrete usage in construction and achieve the objectives of green and low-carbon construction, this study innovatively develops a low-carbon binary material by adding limestone powder (LP) and silica fume (SF) into the conventional cement-based material, enhancing the comprehensive utility value of LP. The experimental results show that the addition of 15% LP and 5% SF increases the yield stress of the mortar yet substantially reduces the plastic viscosity to 2.84 Nmm·min, representing a 44.5% decrease compared to pure cement slurry. This reduction is conducive to long-distance pumping of the cement-based material. Moreover, the addition of 5% SF compensates for the 18.8% (mid-stage, 28-d) and 15.8% (late-stage, 90-d) strength loss in mortar caused by LP while simultaneously improving the strength of the co-mixed system by 10.4% (mid-stage) and 10.8% (late-stage). In the early-stage measurements of the LP-SF binary cement-based materials, it is observed that while SF slightly increases the hydration heat release, LP suppresses the early hydration heat release. Therefore, the total heat release observed in the 15% LP and 5% SF group after 72 h is only 254 J/g, demonstrating favorable temperature control and crack prevention effects. In addition, X-ray diffraction (XRD) and thermogravimetric/differential thermogravimetric (TG/DTG) phase analysis reveal a notable increase of 53.56% in CH consumption. Besides, the weight loss on ignition of C-S-H crystals increases, indicating that the secondary hydration of LP and the pozzolanic reaction of SF promote the production of C-S-H in the system. Combined with the late-stage strength and water absorption characteristics, it is concluded that the system exhibits good mechanical properties and compactness. This study presents a use of mixed proportion that enables excellent mechanical properties, good pumping performance, and low hydration heat. Moreover, the analysis indicates that the carbon emission of each cubic meter of the as-developed mortar is reduced by approximately 16.7–23.9%, promoting the efficient and clean utilization of LP and SF.

Optimization of f-MgO/f-CaO phase in ladle furnace slag by air rapidly cooling

Understanding the Role of Calcium Silicate Slag in Sodium Carbonate-Activated Green Materials: Influence on Kinetics, Strength, and Efflorescence

Evaluating the Effect of MgO/Al2O3 Ratio on Thermal Behaviors and Structures of Blast Furnace Slag with Low Carbon Consumption

The study on the reconstruction and evolution pathway of free lime by hot stage mixing molten ironmaking and steelmaking slags in a laboratory

Effect of CaO on the shrinkage and microstructure of alkali-activated slag/fly ash microsphere

Low carbon cementitious materials: Sodium sulfate activated ultra-fine slag/fly ash blends at ambient temperature

The Influence of CaO and MgO on the Mechanical Properties of Alkali-Activated Blast Furnace Slag Powder

Potential Reuse of Ladle Furnace Slag as Cementitious Material: A Literature Review of Generation, Characterization, and Processing Methods

Evolution of Interface Characteristic between Quicklime and CaO–SiO2–FetO–MgO Melt during Slag‐Forming Procedure in Converter under Different Times

Numerical Investigation of Basic Oxygen Furnace Slag Modification with Gas Bottom-Blowing and SiO2 Modifier

Influence of CaO on Physical and Environmental Properties of Granulated Copper Slag: Melting Behavior, Grindability and Leaching Behavior

Mechanical and Hydration Properties of Ground Granulated Blastfurnace Slag Pastes Activated with MgO–CaO Mixtures

Designing low-carbon MgO–Al2O3–La2O3–C refractories with balanced performance for ladle furnaces

Co-disposal of magnesium slag and high-calcium fly ash as cementitious materials in backfill

The role of CaO and MgO incorporation in chloride resistance of sodium carbonate-activated slag

Preparation and Hydration Mechanisms of Low Carbon Ferrochrome Slag-Granulated Blast Furnace Slag Composite Cementitious Materials

Examining the early-stage performance and mechanical performance of limestone powder-silica fume binary cement-based materials

Exploring influence of MgO/CaO on crystallization characteristics to understand fluidity of synthetic coal slags

Effect of Mineral-Generated Lithium Slag on the Properties of Magnesium Oxychloride Cement

Dissolution of Al2O3–C bricks in 45 wt% CaO-45 wt% SiO2-x wt% CaF2-(10-x) wt% Na2O slag

Study on Foaming Property of LF Refining Slag