Abstract:One of the promising ways to increase fuel and modern gas turbine energy efficiency is using cyclic air intercooling between the stages of high- and low-pressure compressors. For intercooling, it is possible to use cooling in the surface heat exchanger and the contact method when water is injected into the compressor air path. In the presented research on the cooling contact method, it is proposed to use a thermopressor that implements the thermo-gas-dynamic compression process, i.e., increasing the airflow pressure by evaporation of the injected liquid in the flow, which moves at near-sonic speed. The thermopressor is a multifunctional contact heat exchanger when using this air-cooling method. This provides efficient high-dispersion liquid spraying after isotherming in the high-pressure compressor, increasing the pressure and decreasing the air temperature in front of the high-pressure compressor, reducing the work on compression. Drops of water injected into the air stream in the thermopressor can significantly affect its characteristics. An increase in the amount of water increases the aerodynamic resistance of the droplets in the stream. Hence, the pressure in the flow parts of the thermopressor can significantly decrease. Therefore, the study aims to experimentally determine the optimal amount of water for water injection in the thermopressor while ensuring a positive increase in the total pressure in the thermopressor under conditions of incomplete evaporation. The experimental results of the low-consumption thermopressor (air consumption up to 0.52 kg/s) characteristics with incomplete liquid evaporation in the flowing part are presented. The research found that the relative water amount to ensure incomplete evaporation in the thermopressor flow part is from 4 to 10% (0.0175–0.0487 kg/s), without significant pressure loss due to the resistance of the dispersed flow. The relative increase in airflow pressure is from 1.01 to 1.03 (5–10 kPa). Based on experimental data, empirical equations were obtained for calculating the relative pressure increase in the thermopressor with evaporation chamber diameters of up to 50 mm (relative flow path length is from 3 to 10 and Mach number is from 0.3 to 0.8).

Thermodynamic behaviour and heat transfer characteristics of air vessels in water delivery systems

Effects of inlet turbulence intensity on wall heat transfer in a turbine guide vane

Pressure and Flow Characteristic Modeling of Water Hydraulic Axial Piston Pump Based on Variable Fluid Properties

Compensation of Pressure Enthalpy Effects on Temperature Fields for Throttling of High-Pressure Real Gas

Modelling and Experiment Study on Fluid Character of Axial Piston Pump

Thermohydraulic analysis of hybrid smooth and spirally corrugated tubes

Parametric Analysis on Throttling Components of Multi-Stage High Pressure Reducing Valve

Numerical Study of the Thermal Performance of a Hydrogen Pulsating Heat Pipe

Optimal Volume Selection of Air Vessels in Long-Distance Water Supply Systems

Throttling Components Effect on Aerodynamic Performance of Superheated Steam Flow in Multi-Stage High Pressure Reducing Valve

Turbulent Compressible Flow Analysis on Multi-Stage High Pressure Reducing Valve

Performance prediction of HFC, HC, HFO and HCFO working fluids for high temperature water source heat pumps

Numerical Analysis Of Airfoil Naca0015 And Centrifugal Pump'S Cavitation Characteristic Based On The Thermodynamic Effects

Numerical Study of Thermal-Hydraulic Performance Improvement of Enhanced Surface Tubes

Experimental Study of Thermodynamic Effects of Cavitation on Pressure Fluctuation and Radiated Noise in High-Temperature and High-Pressure Water

Effectiveness of Air Admission Through Short Pipes in Reducing Pressure Fluctuation of Propeller Hydro-turbine Flow Channel

Investigation of Thermopressor with Incomplete Evaporation for Gas Turbine Intercooling Systems

Numerical investigation on the thermal-flow performance of humid air-water in the interspace outside staggered tube bundles

Cavitation Flow Characteristics of Water and Liquid Oxygen in the Inducer Considering Thermodynamic Effect

Influence of Thermodynamic Effects on Rotor-Stator Cavity Flow in Liquid Oxygen Turbopump

A Thermodynamic Cavitation Model Applicable to High Temperature Flow