Abstract:The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger π-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (Voc) of 0.99 V, a dramatically increased short-circuit current density (Jsc) of 15.30 mA cm–2, and fill factor (FF) of 61.4% compared to PF1-TS4 (Voc = 0.99 V, Jsc = 11.21 mA cm–2, and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is ∼50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A–D–A-structured fused-ring electron-deficient building blocks.This article has not yet been cited by other publications.

Configurational Isomers Induced Significant Difference in All‐Polymer Solar Cells

Isomerism Strategy to Optimize Aggregation and Morphology for Superior Polymer Solar Cells

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

Regulation of Polymer Configurations Enables Green Solvent-Processed Large-Area Binary All-Polymer Solar Cells With Breakthrough Performance and High Efficiency Stretchability Factor

Molecular Optimization on Polymer Acceptor Enables Efficient All‐Polymer Solar Cell with High Open‐Circuit Voltage of 1.10 V

Improved Molecular Ordering in a Ternary Blend Enables All‐Polymer Solar Cells over 18% Efficiency

Fused perylene diimide-based polymeric acceptors with different π-conjugation and molecular conformation in all polymer solar cells

Precisely Controlling the Position of Bromine on the End Group Enables Well‐Regular Polymer Acceptors for All‐Polymer Solar Cells with Efficiencies over 15%

Improvement in Power Conversion Efficiency of All-Polymer Solar Cells Enabled by Ultrafast Channels for Charge Dynamics

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

A polymer acceptor with double-decker configuration enhances molecular packing for high-performance all-polymer solar cells

Fine‐Tuning Batch Factors of Polymer Acceptors Enables a Binary All‐Polymer Solar Cell with High Efficiency of 16.11%

Rational Design of Perylenediimide-Based Polymer Acceptor for Efficient All-Polymer Solar Cells

High‐Performance Terpolymers with Well‐Defined Structures Facilitate PCE over 19% for Polymer Solar Cells

Over 15% Efficiency Polymer Solar Cells Enabled By Conformation Tuning Of Newly Designed Asymmetric Small-Molecule Acceptors

Effect of Isomerization of Linking Units on the Photovoltaic Performance of PSMA-Type Polymer Acceptors in All-Polymer Solar Cells

Morphology Control Realizes Fast Charge Dissociation and Transport in High-Performance All-Polymer Solar Cells

Benzotriazole-based Polymer Acceptors with Precise Structures for All-polymer Solar Cells

Tailoring polymer acceptors by electron linkers for achieving efficient and stable all-polymer solar cells

Novel polymer acceptors achieving 10.18% efficiency for all-polymer solar cells