Abstract:The Ni-Fe-based superalloy GH4169 (Inconel718) is widely used for several critical gas-turbine components which are hot forged. Its microstructure and property are sensitive to the parameter adjustment during hot working process. To obtain required low-cycle fatigue and fracture properties, it is essential that the microstructure is controlled during preheating and heat treatment. The evolution of non-uniform microstructure during hot working is more complicated than that of uniform microstructure. On the other hand, various secondary phases can be observed in GH4169 alloy, thus it is important to investigate the effect of secondary phases on the microstructure evolution during forging process. In this work, the mechanisms of non-uniform microstructure evolution in GH4169 alloy were studied by analyzing the evolution of secondary phases, grain boundary misorientation, grain size and interactions of dislocation. It is found that the volume fraction of 8 phase increases with the increasing of temperature and heating time at the lower temperature. While at the higher temperature, it decreases monotonously with the temperature increasing, but increases first and then decreases to stable value with time increasing. The pinning effect of secondary phases in GH4169 alloy can be concluded that the gamma '' phase and 8 phase precipitated within the grains retain movement of dislocation, the 8 phase precipitated at the grain boundary hinders the nucleation and growth of recrystallized grains, and the carbides limits the grain growth. The frequency of low angle grain boundary decreases with temperature and time increasing, and the mobility of low angle grain boundary increases with temperature increasing. The uniformity of microstructure and the size of equaxied subgrain increases with heating temperature and time increasing. Continuous recrystallization of elongated grain occurs at specific conditions. The mechanisms of non-uniform microstructure evolution during heating process can be concluded as sub grain growth, recrystallized grain growth, and anneal twinning nucleation and growth. The recrystallized grains are formed by the growth of subgrains conducted by the rotation of low angle grain boundary and the movement of dislocation. When the grain growth is pinned, the mechanisms for the energy dissipation is the nucleation and growth of anneal twinning. And the growth of anneal twinning promotes the generation of low angle grain boundaries at the tip of partial anneal twinning.

A Cellular Automata Model for Recrystallization Annealing of Aged GH4169 Superalloy and Its Application

Formation mechanism of large grains inside annealed microstructure of GH4169 superalloy by cellular automation method

An innovative annealing treatment method and its mechanism to refine deformed mixed grains of initial aged GH4169 superalloy

A novel recrystallization annealing method to cooperatively control the grain size and phase content for initial aged GH4169 superalloy forging

Modeling and Simulation of Dynamic Recrystallization for Inconel 718 in the Presence of Δ Phase Particles Using a Developed Cellular Automaton Model

Mechanisms of Non-Uniform Microstructure Evolution in Gh4169 Alloy During Heating Process

Effect of Deformation Parameters of an Initial Aged GH4169 Superalloy on Its Microstructural Evolution During a New Two-Stage Annealing

A 3D Cellular Automaton with Inhomogeneous Nucleation for Simulating Dynamic Recrystallization of Low-Alloy Steel with Mixed-Grain Microstructure

Atomic Scale Computer Simulation for Ni-Cr-Al Alloy During Re-Ageing Process

Effect of Cooling Recrystallization Annealing Treatment on Properties of an Initial Aged Deformed GH4169 Superalloy

Effect of Aging and Recrystallization Annealing Treatment on Forged Mixed Grain Structure of Ni-based Superalloy

Mathematical Model for Microstructure Evolution of GH4169 Alloy During Hot Working Process

Hot Deformation Characteristics of GH141 Superalloy

Study of static recrystallization behavior in hot deformed Ni-based superalloy using cellular automaton model

Cellular Automaton Modeling of Dynamic Recrystallization of Nimonic 80A Superalloy Based on Inhomogeneous Distribution of Dislocations Inside Grains

Modeling of the Static Recrystallization for 7055 Aluminum Alloy by Cellular Automaton

Effects of Deformation Processing Parameters on the Microstructure Evolution and Microhardness of GH4169 Superalloy during Annealing Treatment

Cellular Automaton Modeling of Dynamic Recrystallization of Ni–Cr–Mo-based C276 Superalloy During Hot Compression

A novel simulation of continuous dynamic recrystallization process for 2219 aluminium alloy using cellular automata technique

Investigation on Mechanism of Microstructure Evolution During Multi-Process Hot Forming of GH4169 Superalloy Forging

2D Cellular Automaton Simulation of Hot Deformation Behavior in a Ni-based Superalloy under Varying Thermal-Mechanical Conditions